Eurolube 53430 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 21

Eurolube 53430 Скачать руководство пользователя страница 8

LUBE-MASTER R10

8(21)

TCM: ‡
TCM MainMenu

PortX: ‡
TCM MainMenu

O:0.000 ‡
Zero adjust

O:-0.120_ ‡
Zero adjust

O:-0.120 ‡
Zero adjust

TCM: ‡
TCM MainMenu

PortX: ‡
TCM MainMenu

C:1.000 ‡
Calibration

C:1.000 ‡
Calibration

C:1.000 ‡
Calibration

TCM: ‡
TCM MainMenu

PortX: ‡
TCM MainMenu

T:6 ‡
Time constant

T:6 ‡
Time constant

T:6 ‡
Time constant

5.3. Analogue sensor settings

5.3.1. Set the input signal filter time constant

This time constant (

Tau

) is used to filter the sensor signal to create an

accurate tank level. “0” means no filter and a higher value gives slower
response but a more accurate value. The default value of “6” is in most cases
good. It means that for a step in the tank level the reading of the level is on
99,9 % after 30 seconds.

Enter menu

[TCM//PortX]

by scrolling with



or



.

At

PortX:

press

ENTER

.

Scroll to

T:

using



or



.

Press

ENTER

to get the cursor.

Type the

time constant

and press

ENTER

to acknowledge. When the

cursor disappears it is finished.

Press

EXIT

two times to leave Set-Up mode.

5.3.2. Adjusting the offset

Offset adjusting is used to obtain “0” volume when the tank is empty. If the
sensor 53417 is used a normal value is –0.080. The “-“ sign is typed on the
keypad by first pressing down arrow (yellow) two times followed by the “?”
mark.

If the tank is empty, put the sensor in the tank at the bottom. If there is fluid
in the tank hold the sensor outside the tank at bottom level. Adjust the offset
value until the tank level shows “0”.

Enter menu

[TCM//PortX]

by scrolling with



or



.

At

PortX:

press

ENTER

.

Scroll to

O:

using



or



.

Press

ENTER

to get the cursor.

Type the

offset value

and press

ENTER

to acknowledge. When the cursor

disappears it is finished.

Press

EXIT

two times to leave Set-Up mode.

5.3.3. Adjusting the calibration

The calibration factor should normally be set to “1.018” if all other values
are set properly. The intention with the calibration factor is to set the
amplification so that the analogue input of the port matches the sensors
output.

Enter menu

[TCM//PortX]

by scrolling with



or



.

At

PortX:

press

ENTER

.

Scroll to

C:

using



or



.

Press

ENTER

to get the cursor.

Type the

calibration value

and press

ENTER

to acknowledge. When the

cursor disappears it is finished.

Press

EXIT

two times to leave Set-Up mode

«
...
6
7
8
9
10
...
»

Содержание 53430






















Отзывы:

Нет отзывов