Eurolube 53430 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 21

Eurolube 53430 Скачать руководство пользователя страница 7

LUBE-MASTER R10

7(21)

TCM: ‡
TCM MainMenu

PortX: ‡
TCM MainMenu

Mask:X ‡
Set Mask 0-15

Mask:X ‡
Set Mask 0-15

Mask:X ‡
Set Mask 0-15

TCM: ‡
TCM MainMenu

PortX: ‡
TCM MainMenu

Tank:X ‡
Set TankNo ???

Tank:X ‡
Set TankNo ???

Hint!

Follow preferably ”Recommendation for setting addresses” when setting addresses.

4.5. Recommendation for setting addresses

Each module demands a unique 16 bit hexadecimal address. There are
some forbidden and some reserved addresses but it is possible to use
all addresses between 0001 and 9999. To make it easier to upgrade
and support the system we recommend using the chart to the right.

This means that the first TSM should have the address 8001 and the
next one 8002 etc. It is a good idea not to use the default address
8000, it makes it easier to add new Tam’s

NOTE! It is essential to add modules to the configuration sheet

continuously as they are configured to avoid collisions.

NOTE!

Address 0000 is forbidden and addresses above 9999 are reserved for the system.

5. Configure the ports

A TSM has four ports that are used to control four different pumps/tanks.

5.1. Connect a tank to a port

[TCM//PortX/Tank]

To set a tank number for a port, from the main menu.

Enter menu

[TSM//PortX]

by scrolling with



or



.

At

PortX:

press

ENTER

.

Press

ENTER

to get the cursor.

Check the number of the tank that is connected to portX, type that number in and
press ENTER to acknowledge. When the cursor disappears it is finished.

Press EXIT two times to leave Set-Up mode.

5.2. Set the Mask

[TCM//PortX/Mask]

Using the Mask each tank function can be set. This is done by
adding the values for the desired functions, in the chart to the right.

EXAMPLE:

Port 1 measures the level of a waste oil tank and

controls the air to a waste oil pump using an Eurolube 2-levels
sensor 53132. This is up done by calculating the value of the Mask 1+4+8=13. The
Mask should be set to 13.

Enter menu

[TCM//PortX]

by scrolling with



or



.

At

PortX:

press

ENTER

.

Scroll to

Mask:

using



or



.

Press

ENTER

to get the cursor.

Type the

mask value

and press

ENTER

to acknowledge. When the cursor

disappears it is finished.

Press

EXIT

two times to leave Set-Up mode.

Adress

Module

0000

Forbidden

1000 – 1xxx

MPDM

2000 – 2998

PM

2999

PC-database

3000 – 3xxx

KeyPad

4000 – 4xxx

LED-display

5000 – 5xxx

PLC-modules

6000 – 6xxx

Reserved

7000 – 7xxx

Reserved

8000 – 8xxx

TCM

9000 – 9xxx

Others

A000 – FFFF

Forbidden

Function

Value

Waste oil tank

1

Not in use

2

Invert B

4

Invert A

8

«
...
5
6
7
8
9
...
»

Содержание 53430






















Отзывы:

Нет отзывов