ETS REJUVASUN 332 Скачать руководство пользователя страница 4

28940-01A

iii

afety Information

Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexposure can cause
eye and skin injury and allergic reactions. Repeated exposure may cause premature aging of the skin and skin

cancer. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES.
Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before using sunlamp if you are
using medications or have a history of skin problems or believe yourself especially sensitive to sunlight. If you do not tan in the sun, you
are unlikely to tan from the use of this product. Children, the elderly, or fair skinned people who always burn easily and either never tan
or tan minimally should not use this equipment.

To use, lie down under canopy and pull down as far as adjustment will allow. Minimum use distance from face tanner is 4 inches (10.2
centimeters), otherwise overexposure may occur. Minimum use distance elsewhere is touching the clear plastic panels. Do not use with-
out clear plastic panels in place. Untanned persons should not tan on consecutive days during their first week of tanning. Never tan more
than once a day. Tanning normally appears after the first few sessions and maximizes after approximately four weeks. Tan once or twice
per week thereafter to maintain appearance. Persons already having a base tan may begin at advanced levels corresponding to the
extent of their base tan.

New lamps emit approximately 10% more ultraviolet radiation during the first 50 hours of operation. Recommended tanning times should
therefore be reduced by approximately 10% during that period.

WARNING:

• Read the instructions booklet before using this sunlamp product. • All persons in the room should wear protective eyewear

when lamps are on. Required eyewear: Ultra SunGlobes®, 

special-eyez, or other dark-tinted eyewear that meet 21 CFR 1040.20 guide-

lines. Other types of eyewear may not provide adequate protection. Failure to use protective eyewear may result in severe burns or other
eye injury. If discomfort develops, discontinue use and consult a physician.

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:

Velocity® Wolff® Model VEL71-T12 / 100W PREHEAT-BIPIN

(Bench lamps)

Velocity® PLUS Wolff® Model VLP71-T12-100W Bi-Pin

(Canopy lamps)

Heraeus E400 HPT

-or- 

Philips Model HPA 400/30s

-or- 

CosmoTech Model 23045

(SolarMax™ IFT facial unit)

THIS EQUIPMENT MUST BE EARTH GROUNDED. 

This product is in conformity with performance standards for sun lamp products under 21 CFR PART 1040.20 and
ANSI/UL Standard 482. Certified to CAN/CSA Standard C22.2 NO. 224.

LABELING NOTICE:

Labels are affixed on all systems to inform the user of possible dangers. Regulations are stated in 21 CFR, Section

1040.20, and require that all products manufactured after September 8, 1986 which use sunlamps must display the following:

DANGER

88465

RECOMMENDED EXPOSURE TIMES IN MINUTES

MAXIMUM EXPOSURE TIME IS 20 MINUTES

Level 1/Week 1

Level 2

Level 3

Level 4

Level 5

Skin Type:

1st-3rd Sessions

I

Sensitive Skin

(Burns easily and severely and does not tan.)

NOT RECOMMENDED FOR TANNING

II

Light

(Burns easily and severely and tans minimally.)

4

8

12

16

20

III

Normal

(Burns moderately and tans average.)

6

10

15

20

20

IV

Dark

(Burns minimally, tans easily and above average.)

8

12

16

20

20

DISCONNECT POWER BEFORE ATTEMPTING TO CLEAN, RELAMP, OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT.

Содержание REJUVASUN 332





































Отзывы: