ETS NORD EOZ-1 Скачать руководство пользователя страница 26

Страница: 26 / 28

www.etsnord.com

RDM-59-0322

NORD

canopy

EOZ installation guide

Control Panel display messages

When ”ETS NORD Canopy system” is lit in

white, the system is operating normally.

Call service is blinking:

This indicates that the system is operating

normally, but it is time for its annual

maintenance.

Call service is lit:

pressure warning.

This indicates the system is not operating due

to a pressure warning. Check that all grease

filters are correctly installed in the extraction

chamber of the canopy, and that the bottom

edges of all filters do not have any gaps.

Call service is lit is red:

This indicates a technical fault has been

detected in the system. Contact your ETS

NORD representative or nearest authorized

service company as soon as possible at:

www.etsnord.com/service

For further assistance, contact your ETS NORD representative or nearest authorized service company.
Visit: www.etsnord.com/service

NOTE!

Cooking in the kitchen may continue when Control Panel alarm is active as long as there is no

sign of ozone. Still service is required and information must be provided to ETS NORD representative or

nearest authorized service company

Содержание EOZ-1





























Результаты поиска

Содержание EOZ-1

Отзывы:

Похожие инструкции для EOZ-1

Бренды по названию

Популярные бренды

ETS NORD EOZ-1, Руководство по установке

Результаты поиска

Содержание EOZ-1

Отзывы:

Похожие инструкции для EOZ-1

Бренды по названию

Популярные бренды