background image

 

 

6

If the MNPR™ is operating in a mode other than Sensitive (standard), then the 
Programmer will display the variables unique to the present operating mode: 

 

4.  Time Delay Mode

 - In addition to RV, RA and ST, Relay Actual will allow the 

user to set the Time Delay, Instant Current and Extended Delay. 

 

5. Insensitive Mode

  - In addition to RV, RA and ST, the user will be able to 

program the Insensitive Trip Current and Extended Delay. 

 

6. Watt-Var Mode

 - In addition to RV, RA and ST, the user may program the 

Watt-Var Current as well as the Watt-Var Angle. 

 

IV. Determining the Network’s system Condition 

 

In addition to programming the MNPR™, the Programmer can be used to gain 
valuable information about the status of the network.  These functions are located on 
the third row from the top. 

 

A. Network Volts

 (Va:, Vb:, Vc:) - Press 

A, 3

.  This will tell the user the voltage 

present on the network side of the network protector. 

 

Note: On 480-volt network protectors, the MNPR™ maybe on the 120-volt 
side of the potential transformers.  In this case, the display should be 
multiplied by 2.2 to calculate the actual network voltage. 

 

B. Network Amps

 (Ia:, Ib:, Ic:) - Press 

B, 3

. This will tell the user the current flowing 

through the network protector. 

 

C. Reclose Volts

  (Da:, Db:, Dc:) - Press 

C, 3

. This will tell the user the present 

differential voltage between the transformer and network sides of the network 
protector. 

 

D. Relay Temp

 (Tf:, Tc:) - Press 

D, 3

. This will tell the user the temperature inside 

the casing.  In addition, pressing 

NEXT

 will change the display units from Celsius 

to Fahrenheit. 

 

Note: This temperature will generally be higher than the ambient 
temperature because the MNPR™ does generate some internal heat. 

 
V.  Direct Orders to the MNPR™ 

 

The programmer is capable of ordering the MNPR™ to Open and of ordering the 
MNPR™ to Block the network protector from closing.  From the 

“ETI  _ _”

 Scroll: 

 

A. Block Relay

 - Press 

B, 4

. This will prevent the MNPR™ from closing the 

protector.  If the protector is already closed, this feature will not cause it to open. 

Содержание MNPR












Отзывы: