background image

Important safety recommendations 

 

FAILURE  TO  COMPLY  WITH  THE  FOLLOWING  SAFETY  RECOMMENDATIONS  MAY 

RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE. 

 

1. 

PLEASE  READ  CAREFULLY  AND  ADHERE  TO  ALL  SAFETY  AND  INSTALLATION 

RECOMMENDATIONS. 

2.  The opener is designed and manufactured to meet local regulations. The installer must be 

familiar with local regulations required in respect of the installation of the opener. 

 

3.  Unqualified  personnel  or  those  persons  who  do  not  know  the  occupational  health  and 

safety  standards  being  applicable  to  automatic  gates  and  other  doors,  must  in  no 

circumstances carry out installations or implement systems.

 

4.  Persons who install or service the equipment without observing all the applicable safety 

standards will be responsible for any damage, injury, cost, expense or claim whatsoever 

any person suffered as a result of failure to install the system correctly and in accordance 

with the relevant safety standards and installation manual whether directly or indirectly.

 

5.  For additional safety we strongly recommend the inclusion of Photo Beam. Although the 

opener incorporates a pressure sensitive Safety Obstruction Force system the addition of 

Photo Beam will greatly enhance the operating safety of an automatic garage door and 

provide additional peace of mind.

 

6.  Make sure that the garage door is fully open & stationary before driving in or out of the 

garage.

 

7.  Make sure the garage door is fully closed & stationary before leaving.

 

8.  Keep hands and loose clothing off the opener and garage door all the time.

 

9.  The  Safety  Obstruction  System  is  designed  to  work  on  STATIONARY  objects  only. 

Serious  personal  injury,  death  and  /  or  property  damage  may  occur  if  the  garage  door 

comes into contact with a moving object

 

10. 

This appliance is not intended for use by persons (including children) with reduced 

physical,  sensory  or  mental  capabilities,  or  lack  of  experience  and  knowledge, 

unless  they  have  been  given  supervision  or  instruction  concerning  use  of  the 

appliance by a person responsible for their safety. Children should be supervised 

to ensure that they do not play with the appliance. 

11. 

Waste  electrical products  should  not  be  disposed  of  with  household  waste. 

Please recycle where facilities exist. Check with your local authority or retailer for 

recycling advice. 

12. 

If the supply cord is damaged, it must be replaced by the manufacturer, its service 

agent or similarly qualified persons in order to avoid a hazard. 

WARNING: Important safety instructions. It is important for the safety of persons to 

follow all instructions. Save these instructions. 

Do not allow children to play with door controls. Keep remote controls away from 

children. 

Watch the moving door and keep people away until the door is completely opened 

or closed. 

Take  care  when  operating  the  manual release  since  an  open  door  may  fall  rapidly 

due to weak or broken springs, or being out of balance. 

Frequently  examine  the  installation,  in  particular  check  cables,  springs  and 

mountings  for  signs  of  wear,  damage  or  imbalance.  Do  not  use  if  repair  or 

adjustment is needed since a fault in the installation or an incorrectly balanced door 

Содержание ET-1000E




















Отзывы: