manualshive.com logo in svg

ETC Unison ERn2-W, Руководство по установке

Поделиться
Скачать
ETC Unison ERn2-W Скачать руководство пользователя страница 7

Introduction

3

ERn-NET 7180A1400 ERn Ethernet Switch 

Module

The ERn-NET module provides four ports of 802.3af 
compliant Power over Ethernet (PoE) and one port for the P-
ACP.
• Not compatible with a rack-mount ERn enclosure.
• Not compatible with ERn4 230 VAC enclosures.

UBPO

7180A1411 Unison Battery Pack 

Option Kit

The UBPO provides back-up power during power outages for 
the P-ACP for up to 90 minutes for an ERn enclosure with 
one P-ACP or up to 45 minutes for an ERn4 with two P-ACPs 
installed.
• Not compatible with a rack-mount ERn enclosure.

URTO

7180A1410 Unison Ride Thru 

Option Kit

The URTO kit provides power for one P-ACP in the host 
enclosure for a limited time (minimum of 12 seconds) during 
brief power outages or drop outs.
• If installed in an ERn4 enclosure, one URTO is required per 

installed P-ACP.

ERn-BM

7180A1402 Blank Module

The ERn-BM is required for any empty module space in the 
ERn enclosure. 
• Installs into the accessory option module slot of an ERn 

enclosure.

ERn-RPS

7180A1401 ERn Redundant 

Power Supply

The ERn-RPS provides an additional rack power supply that 
powers the ERn enclosure if the primary rack power supply is 
removed or fails.
• Tool-free installation into the accessory option slot of an 

ERn enclosure.

• Not supported in ERn4 230 VAC enclosures. The 

ERn4 230 VAC enclosure requires two rack power supplies 
as standard.

Model

Part 

Number

Description

Notes

Содержание Unison ERn2-W









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды