manualshive.com logo in svg

ETC Unison ERn2-W, Руководство по установке

Поделиться
Скачать
ETC Unison ERn2-W Скачать руководство пользователя страница 27

Final Installation and Power Up

23

enclosure, or only a Paradigm Station Repeater module (P-REP) in the top module slot with an 
blank module below.

4:

Install either the ERn blank option module, the ERn ethernet switch Module (ERn-NET), or the 
Redundant Power Supply (ERn-RPS) in the lower option module slot.

a: If installing the ERn ethernet switch Module (ERn-NET) or the Redundant Rack Power Supply 

(ERn-RPS) module in the option module slot, be certain you have completed the installation 
requirements. See 

Install Rack Options

 on 

page 24

.

5:

Install blank module in any unused module slot in the enclosure to maintain the required 
convection cooling requirements.

Note:

Neither the Redundant Power Supply (ERn-RPS) nor the Ethernet Switch module 

(ERn-NET) are supported in an ERn4 enclosure at 230 VAC. Instead, an ERn4 at 

230 VAC is shipped from the factory with a rack power supply installed in the top 

(normal) position and in the lower option module slot as standard.

Содержание Unison ERn2-W









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды