ETC GDS BluesSystem Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

background image

Introduction

2

Help from ETC Technical Services

If you are having difficulties, your most convenient resources are the references given in this
document. To search more widely, try the ETC website at

www.etcconnect.com

. If none of

these resources are sufficient, contact ETC Technical Services directly at one of the offices
identified below. Emergency service is available from all ETC offices outside of normal
business hours.

When calling for help, please:

• Have a detailed description of the problem
• Be near the equipment for troubleshooting
• Have a notification number if you have called in previously

Safety

BluesSystem products are intended for professional use only.

Read the entire manual

before using this equipment.

Americas

United Kingdom

Electronic Theatre Controls Inc.

Electronic Theatre Controls Ltd.

Technical Services Department

Technical Services Department

3031 Pleasant View Road

26-28 Victoria Industrial Estate

Middleton, WI 53562

Victoria Road,

800-775-4382 (USA, toll-free)

London W3 6UU England

+1-608 831-4116

+44 (0)20 8896 1000

[email protected]

[email protected]

Asia

Germany

Electronic Theatre Controls Asia, Ltd.

Electronic Theatre Controls GmbH

Technical Services Department

Technical Services Department

Room 1801, 18/F

Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square

83607 Holzkirchen, Germany

9 Sheung Yuet Road

+49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong

[email protected]

+852 2799 1220

[email protected]

«
...
3
4
5
6
7
...
»

Содержание GDS BluesSystem





























Отзывы:

Нет отзывов

Похожие инструкции для GDS BluesSystem

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Farmi Forest Corporation Страницы: 32

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: M-Audio Страницы: 25

Бренд: YOKOGAWA Страницы: 75

Бренд: Yetter Страницы: 24

BOMAG BVP 12/50 A

Бренд: Fayat Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды