ETC GDS BluesSystem Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 28

background image

23

BluesSystem Installation Manual

Configure Switched Output Level

Set Output Level

A rotary potentiometer is provided on Switched power supplies to set the intensity level for
connected BlueBeam and BlueDome fixtures when the unit is switched to On.

Step 1:

To set the output level, power the BlueBeam and BlueDome fixtures and switch the
fixtures to On.

Step 2:

Use a precision screwdriver to change the rotary potentiometer (labeled TopSet) until the
desired intensity level on the fixtures is reached.

WARNING:

RISK OF ELECTRIC SHOCK! Mains voltage is present inside the power
supply during this procedure. It is important to note that electrical
equipment can present an arc flash safety hazard if improperly
serviced. Any work on energized equipment must comply with OSHA
Electrical Safe Working Practices.

Note:

To effectively use this feature, you will need to have line of sight between power

supply and the connected fixtures.

TOPSET

VR1

«
...
24
25
26
27
28
»

Содержание GDS BluesSystem





























Отзывы:

Нет отзывов

Похожие инструкции для GDS BluesSystem

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: LAZBOY Страницы: 9

Бренд: M-Audio Страницы: 3

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

bionic power knee

Бренд: Össur Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды