background image

26

www.eta.co.at

Commissioning

7

Commissioning

Monitoring the screw joints

Due to vibration and thermal expansion, all screw
joints  must  be  inspected  and  tightened  prior  to

commissioning. 

Bleeding before commissioning

The  fresh  water  module  must  be  ventilated  before
commissioning.  For  ventilation,  there  is  a  ventilation
screw on the top of the fresh water module.

Fig. 7-1: Bleed screw

The option [Automatic venting] has been enabled
at  the  factory.  In  this  way,  the  controller

recognises  the  introduction  of  air  into  the  heat
exchanger and tries to remove it with the help of both
pumps.  This  can  also  take  place  multiple  times  one
after the other.
If, however, the water is still not sufficiently warm, there
is  still  air  in  the  plate  heat  exchanger  and  manual
venting is needed. To do this, carry out the following
steps.

Venting the fresh water module

1. Open  the  hot  water  tap  in  the  drinking  water

network  so  that  the  fresh  water  module  pumps
start.

2. After  about  15 seconds,  close  the  hot  water  tap

again.

3. Open the vent screw in the fresh water module and

allow the air to escape.

4. Then open the hot water tap once more and carry

out  the  steps  again.  Carry  on  doing  this  until  no
more air escapes from the fresh water module.

Mounting the plastic cover

Reattach  the  plastic  cover  following  commissioning.
Pull off the protective film and affix the ETA logo in the
corresponding recess.

Adjusting the speed of the circulation pump

By  default,  the  circulation  pump  is  set  to  "Constant
Speed" in the "III" position.  If required, the operating
mode "differential pressure variable (Δp-v)" (left scale
on the rotary knob) can also be set.

Fig. 7-2: Factory pump settings

Using the current flow rate (readable in the text menu
of  the  ETAtouch  control)  and  the  pump  curve  (see
pump  characteristics),  the  speed  of  the  circulation
pump can be adapted to the customer's requirements. 

We recommend adjusting the pump so that a flow
rate  of  approximately  4 l/min  is  achieved.  A

minimum  flow  of  2 l/min  must  be  guaranteed  for  the
flow sensor to trigger.

Thermal valves for the circulation line are actually
not required, because the circulation pump shuts

down in time by means of the return sensor. If there are
several  strands  available  for  the  circulation  line  and
thermal  valves  are  installed  in  these,  at  least  one
strand must always remain open (the longest strand, if
possible) so that circulation can occur.

Содержание Fresh water module 33













































Отзывы: