eta ePE-K 140 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 84

background image

52

www.eta.co.at

Attaching pellet hoses

Installation

Install the thermal emergency cooling valve on the
boiler. The connections for the safety heat exchanger
are on the opposite side of the boiler.

Fig. 9-48: Thermal emergency cooling valve

Installing the safety valve, pressure gauge and
bleed valve

A safety valve, pressure gauge and bleed valve must
be installed on the boiler. They are not included in the
delivery scope.

DANGER!

Safety valve outlet

The safety valve outlet must be directed to the ground
in a pipe so nobody is endangered by hot water or
steam.



The safety valve outlet must be fed to the sewage
system (e.g. duct) via a clearly visible, open route
(siphon funnel), This will ensure that malfunctions,
especially a failure of the safety valve to close, can
be detected. If no connection is available to the
sewage system, the outlet must be directed to the
ground in a pipe.

9.11

Attaching pellet hoses

Note instructions about laying pellet hoses

When laying the pellet hoses, take note of the
comments; see

11.7 "Information about pellet

.

Reinforced pellet hoses are required

Reinforced pellet hoses are also required due to the
higher pellet discharge rate. They have a larger
external diameter and require larger hoses clamps. All
these components are available separately from ETA.

Mounting fire protection sleeves (if required)

If the pellet hoses from the storeroom are routed
over a fire section (for example a room in-

between) to the boiler room, fire protection sleeves
must be fitted over both pellet hoses. In wall ducts, a
fire protection sleeve must be mounted on each side,
with ceiling ducts only positioned on the ceiling side.

Fig. 9-49: Fire protection sleeve

Use  the  supplied  concrete  screws  to  fasten  the  fire
protection sleeve. These screws are screwed directly
into the wall by pre-drilling, but without dowels.
In  the  event  of a fire, the  internal material of  the  fire
protection sleeve expands and thus closes the pellet
hoses.  This  prevents  burn-back  in  rooms  through
which the pellet hoses are fed.

CAUTION!

The copper wires must have good contact with the
connections for the pellet hoses.

Otherwise the hoses will not be earthed with the boiler
and there is a risk of electrostatic charge build-up.



Remove the paint or the coating from both pellet
hose connections.

«
...
50
51
52
53
54
...
»

Содержание ePE-K 140





















































































Отзывы:

Нет отзывов

Похожие инструкции для ePE-K 140

MILBORNE 381 Series

Бренд: Hamworthy Страницы: 72

Бренд: Keston Страницы: 72

Бренд: Zip Страницы: 16

Бренд: Ideal Boilers Страницы: 4

Бренд: Vulcan-Hart Страницы: 2

ARCEUS 12 kW MT

Бренд: E.C.A. Страницы: 38

Бренд: Sime Страницы: 12

Бренд: Magikitch'n Страницы: 15

Бренд: OSO HOTWATER Страницы: 48

Бренд: Thermo-Dynamics Boiler Страницы: 28

Бренд: ICI Caldaie Страницы: 32

Бренд: ICI Caldaie Страницы: 36

Бренд: ICI Caldaie Страницы: 40

Evolution EV AC

Бренд: DOMUSA Страницы: 40

Бренд: DOMUSA Страницы: 76

Бренд: Ideal Boilers Страницы: 40

Classic FF 380 P

Бренд: Ideal Boilers Страницы: 40

Бренд: Ideal Boilers Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды