manualshive.com logo in svg

eta ePE-K 140, Руководство по установке

Поделиться
Скачать
eta ePE-K 140 Скачать руководство пользователя страница 22

22

www.eta.co.at

General information

Information for installation

measurement opening because, otherwise, turbulence
at  the  measurement  points  will  prevent  meaningful
measurements.  The  clearance  from  the  boiler's  flue
duct connection or from a pipe bend must be at least
twice the diameter of the flue duct.

Deflagration damper

The  boiler  is  designed  with  safety  routines  in  the
control system to prevent deflagrations. Thus, no def-
lagration damper (also often called an explosion flap)
is required for a boiler output up to 50 kW if the flue
pipe is short and ascends to the chimney.

Fig. 7-6: Example: deflagration damper with draught limiter

We recommend using a deflagration damper for boiler
outputs  of  60 kW  and  up.  A  deflagration  damper  is
required for boiler outputs of 100 kW and up. While the
most that can happen in smaller boilers in the event of
a deflagration is that the flue pipe to the chimney can
be  pulled  apart,  in  larger  boilers  the  gas  volume  is
already so large that a boiler door can be blown off.
For high points before descending sections or at the
beginning of a long horizontal section (L > 20 x D), a
deflagration damper is required regardless of the boiler
output.

DANGER!

Position of the deflagration damper

Position the deflagration damper so that no people
are endangered.

7.1.2

Renovation

Chimney renovation before it's too late

Compared  to  older  boilers,  modern  ones  are  more
efficient and have lower amounts of flue gas and con-
siderably lower temperatures. 
Chimneys with a "too large diameter", in particular, can
no  longer  be  heated  adequately.  The  moisture
contained  in  the  flue  gas  condenses  in  the  chimney,
resulting in the very slow but inexorable destruction of
old masonry chimneys. 

Furthermore, the exit velocity and temperature are too
low if the diameter of the chimney is too large. The flue
gas  then  lacks  the  energy  to  rise  and,  in  extreme
cases, the smoke can sink down along the roof. 
If  your  chimney  does  not  have  a  moisture-resistant
liner  or  its  diameter  is  too  large,  it  will  require
renovation  in  the  form  of  a  new,  moisture-resistant
liner. Narrow chimneys can also be renovated by the
addition of stainless steel pipes. 
Also keep in mind that chimneys have a limited service
life.  Timely  renovation  before  destruction  of  the
chimney  wall  can  be  achieved  quickly  and  easily  by
inserting a tube. But if the flue gas condensates have
penetrated the mortar joints, the entire chimney must
be dismantled and rebuilt.

Chimney renovation with a stainless steel pipe

Maybe the chimney has already been renovated for oil
or  gas  with  a  stainless  steel  pipe,  and  now  a
conversion  to  wood  or  pellets  is  planned.  Or  the
chimney is too narrow to install a ceramic pipe with a
reliable  seal.  If  a  moisture-resistant  inner  pipe  is
installed  in  a  sufficiently  fire-resistant  casing,  the
German Association  of  Chimney  Sweeps  has  found
the following solution to the standards and regulations
dilemma: "in the certification of suitability and safe use
for heating systems, it should be noted that after a soot
fire  the  long-term  durability  cannot  be  ensured  and
penetration  of  the  chimney  by  moisture  cannot  be
ruled  out  so  that  it  may  be  necessary  to  replace  the
inner pipe (Criteria for Determination of Suitability and
Safe  Use  of  Heating  Systems  -  October  29th  2008,
page 12).

Replace inner pipe after a soot fire

After  a  soot  fire,  the  inner  pipe  is  in  all  likelihood  no
longer  sufficiently  leakproof,  making  the  chimney
subject to damage by moisture. In this case, the inner
pipe  needs  to  be  replaced  without  fail,  regardless  of
whether its resistance to soot fires has been checked
or not.

7.2

General information

Approval

All heating systems require approval. Enquire at your
building authority and ask your chimney sweep.

Antifreeze

If  the  building  is  unoccupied  for  longer  intervals  in
winter,  up  to  30%  antifreeze  can  be  added  to  the
heating water. To compensate for the disadvantage of
reduced heat capacity and increased flow resistance,
only slightly higher flow temperatures are needed.

Содержание ePE-K 140





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды