20
21
EN
C
omments
:
•
When you set the alarm frequency, you can choose between:
- "1-5": from Monday to Friday
- "1-7": every day
- "6-7": weekend only
- "1", "2", "3", "4", "5", "6", "7": one day only (each number corresponds to a day of the week,
for example, "1" corresponds to Monday)
•
When an alarm is programmed, you can display the alarm time whenever you want by briefly
pressing the Alarm 1
or Alarm 2
button. The programmed alarm time is displayed and
disappears after a few seconds.
SNOOZE FUNCTION
When the alarm goes off, "
AL1
" or "
AL2
" starts flashing. Press the button
. The alarm stops and
will come back on again after
9 minutes
.
TURNING OFF THE ALARM
When the alarm goes off, "
AL1
" or "
AL2
" starts flashing. Press on
to mute the alarm, then on
to turn it off.
C
omments
:
•
This operation enables you to automatically reactivate the alarm for the next day.
•
If you take no action, the alarm will ring for
30 minutes
.
ENABLING AND DISABLING THE ALARM FUNCTION
To enable or disable a preset alarm, press and hold down the Alarm 1
or Alarm 2
button.
"
AL1
" or "
AL2
" appears/disappears next to the time shown on the luminous display screen.
Listening to radio
1.
To listen to the radio, press the
button to enable the MUSIC function.
2.
Then select RADIO mode by pressing on the
SOURCE
button to scroll through the modes. The
selection cycle is as follows:
Radio > Nature sounds > Auxiliary source
The RADIO mode is indicated by the display of the frequency.
Extend the antenna wire on the back of the device for better FM reception.
3.
To automatically scan for frequencies, press and hold the
(decrease) or
(increase)
button. The scan stops when a radio station has been found. To interrupt the scan, press briefly
on either of buttons again.
4.
To do a manual search, briefly press on the
(decrease) or
(increase) button. With each
press, the frequency decreases or increases by
0.1 MHz.
5.
To turn off the radio, briefly press the
button.
Setting the alarm
In addition to the sunrise simulator, your radio alarm clock allows you to programme 2 alarms at
different times. To do this, the time must have been set beforehand (see previous paragraph). You
can select:
•
the buzzer or
•
the radio, or
•
the "Nature sounds" programme.
Note:
to set the alarms, the MUSIC function must be disabled. To turn off the MUSIC function,
press the
button.
1.
To start setting the alarm, press on Alarm 1
or Alarm 2
.
2.
To start the setting cycle, long press on Alarm 1
or Alarm 2
. The hour digit flashes.
3.
To scroll through the different setting steps, press once or several times on Alarm 1
or
Alarm 2
.
The setting cycle is as follows:
Hour > Minute > Alarm frequency > Type of alarm > Light intensity.
When one of the setting steps has been selected, it starts to flash.
4.
Use the
(decrease) and
(increase) buttons to reach the number you want. To make the
numbers scroll faster, keep the button pressed down.
5.
To save the number, press on Alarm 1
or Alarm 2
. The digit stops flashing and the setting
cycle automatically moves to the next step.
6.
When the alarm has been set,
AL1
or
AL2
is displayed next to the time on the luminous
display screen.
Type of alarm:
"BUZZER" mode
"RADIO" mode
"NATURE SOUNDS"
mode
Sign on the display
screen
"bu"
Last frequency
diffused
"nS"
Additional step(s) of
the setting cycle
/
- Adjusting the
volume
- Choosing the nature
sound ("n-1", "n-2" or
"n-3")
- Adjusting the
volume
Intensity of luminous alarm:
You can adjust the intensity of luminous alarm: "
L01
" to "
L20
" or switch it to the
OFF
position.
•
30 minutes before the alarm time, the lamp lights up at the level "
L01
".
•
The light intensity increases gradually, until it reaches the programmed level.
•
If you programme an alarm less than 30 minutes before the time displayed, the lamp does
not light up.
