ESD EPPC-T10 Скачать руководство пользователя страница 4

Classification of Warning Messages and Safety Instructions

  

This manual contains noticeable descriptions, warning messages and safety instructions, which
you must follow to avoid personal injuries or death and property damage.

This is the safety alert symbol.  
It is used to alert you to potential personal injury hazards. Obey all safety messages
and instructions that follow this symbol to avoid possible injury or death.

DANGER, WARNING, CAUTION

Depending on the hazard level the signal words DANGER, WARNING or CAUTION are used to
highlight safety instructions and warning messages. These messages may also include a warning
relating to property damage. 

DANGER

Danger statements indicate a hazardous situation which, if not avoided, will result in 
death or serious injury.

WARNING

Warning statements indicate a hazardous situation that, if not avoided, could result in 
death or serious injury.

CAUTION

Caution statements indicate a hazardous situation that, if not avoided, could result in
minor or moderate injury.

NOTICE

Notice statements are used  to  notify  people on  hazards  that   could  result   in things  other  than
personal injury, like property damage.

NOTICE

This NOTICE statement indicates that the device contains components sensitive to 
electrostatic discharge. 

NOTICE

This NOTICE statement contains the general mandatory sign and gives information that
must be heeded and complied with for a safe use.

INFORMATION

INFORMATION

Notes to point out something important or useful.

 

Page 4 of 37

Hardware Manual • Doc. No.: I.2007.21 / Rev. 1.1

EPPC-T10

Содержание EPPC-T10






































Отзывы: