ESD EPPC-T10 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 37

ESD EPPC-T10 Скачать руководство пользователя страница 20

Hardware Installation and Change of Battery

5. Hardware Installation and Change of Battery

NOTICE

Read the safety instructions at the beginning of this document carefully, before
you start with the hardware installation!

DANGER

Hazardous Voltage -

Risk of electric shock

due to unintentional contact with

uninsulated live parts with high voltages inside of the system into which the EPPC-T10 is
to be integrated.
→ Disconnect all hazardous voltages (mains voltage) before opening the system.
→ Ensure the absence of voltage before starting any electrical work.
→ Cover or block off adjacent live parts.

NOTICE

Electrostatic discharges may cause damage to electronic components.

→

→

To avoid this, discharge the static electricity from your body

before

you touch the

EPPC-T10.
Furthermore, you should prevent your clothes from touching the EPPC-T10, because
your clothes might be electrostatically charged as well.

5.1 Installation

Procedure:

1.

Discharge your body as described above.

2.

If necessary configure the hardware (dip switches or jumper) before you start with the
installation. See chapter “Prepare Configuration (DIP-Switches, JP800)” page 23.

3.

Make sure that no risk arises from the system into which the EPPC-T10 shall be inserted.

DANGER

Hazardous Voltage

Risk of electric shock

due to unintentional contact with uninsulated live parts with

high voltages inside of the system into which the EPPC-T10 is to be integrated.

→
→

→
→

Disconnect all hazardous voltages (mains voltage) before opening the system.
If the system does not have a flexible mains cable, but is directly connected to
mains, disconnect the power supply via the safety fuse and make sure that the fuse
cannot switch on again unintentionally (i.e. with caution label).
Ensure the absence of voltage before starting any electrical work
Cover or block off adjacent live parts.

4.

Mount the EPPC-T10 on the carrier rail.

5.

Connect the interfaces (Ethernet, Serial, USB, 24 V power supply voltage).

6.

Connect the system to mains again (mains connector or safety fuse).

7.

Switch on the system and the peripheral devices.

8.

End of hardware installation.

9.

Set the interface properties in your operating system. Refer to the documentation of the
operating system.

Page 20 of 37

Hardware Manual • Doc. No.: I.2007.21 / Rev. 1.1

EPPC-T10

«
...
18
19
20
21
22
...
»

Содержание EPPC-T10






































Отзывы:

Нет отзывов