manualshive.com logo in svg

ESAB HandyPlasma 380, Инструкция по эксплуатации

Поделиться
Скачать
ESAB HandyPlasma 380 Скачать руководство пользователя страница 17

17

SECTION  2

  INSTALLATION

Torch comes factory installed. These instructions are
for torch replacement.

Before making any connections to the power source
output terminals, make sure that all primary input
power to the power source is deenergized (off) at the
main disconnect switch and that the input power cable
is unplugged. For operator safety, the torch connec-
tions are loaded.

 front

rear

Torch Connection

Figure 2-2.  Torch Connection

2.6  SECONDARY (OUTPUT) CONNECTIONS

1.

Connect your air supply to the inlet connection of the
filter-regulator.  See Figure 2-1.

2.

Thread the power cable and switch lead of the PT-31XL
through the lower left side bushing of the front panel.
Connect power cable to the torch fitting (left-hand
threads) and connect torch trigger switch leads to pins
1 and 2 of white plug located in the lower right corner
of machine. Make sure the power cable connection is
wrench-tight.

3.

Replace the machine cover panel.

1.

Remove the machine cover panel.  The torch connec-
tion is located on the lower side of machine.  See
Figure 2-2 below.

2.6.1 Torch Replacement

2.6.2 Air Connection

1.

Clamp the work cable to the workpiece. Be sure the
workpiece is connected to an approved earth ground
with a properly sized ground cable.  See Figures 2-3,
2-4 and 2-5.

2.6.3 Work Lead Connection

Содержание HandyPlasma 380













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды