Epson U675 - TM Color Dot-matrix Printer Скачать руководство пользователя страница 171

Страница: 171 / 325

Rev.D

Adjusting and Setting 3-3

TM-U675/U675P (with autocutter) Service Manual

Confidential

2. While pressing the tab of the lever drive coil (type B), rotate the lever motor reduction gear

in the direction indicated in the illustration, so that the protrusion on the lever drive gear
faces the very bottom of the printer.

Figure 3-2

3. Remove your finger from the claw of the lever drive coil (type B). Check that the claw

returns to its original position. Redo from step 1 if it has not returned to its original position.

Figure 3-3

Lever motor reduction gear

Lever drive gear protrusion

Lever drive gear

Lever drive coil (type B)

Содержание U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Результаты поиска

Содержание U675 - TM Color Dot-matrix Printer

Отзывы:

Похожие инструкции для U675 - TM Color Dot-matrix Printer

Бренды по названию

Популярные бренды

Epson U675 - TM Color Dot-matrix Printer, Руководство по обслуживанию

Результаты поиска

Содержание U675 - TM Color Dot-matrix Printer

Отзывы:

Похожие инструкции для U675 - TM Color Dot-matrix Printer

Бренды по названию

Популярные бренды