Epson U675 - TM Color Dot-matrix Printer Скачать руководство пользователя страница 224 | Manualshive

Страница: 224 / 325

Epson U675 - TM Color Dot-matrix Printer Скачать руководство пользователя страница 224

Appendix D-36

Product Overview

Rev.D

Confidential

Cutter Blade Mechanism

The following parts are established on the movable cutter blade shaft that is that is attached to
the cutter frame.

❏

Stationary blade

❏

Scissors blade spacer

❏

Scissors blade

❏

Movable blade pressure spring

❏

Movable blade spring washer

An oblong hole is designed to abut the movable blade drive shaft that is fastened to the cutter
drive gear on the scissors blade.  Reciprocal rotation of the cutter drive gear supportingly rotates
the movable blade shaft of the scissors blade.  The sliding blade bearing and sliding blade are
established on the sliding blade shaft and sliding blade link shaft that are attached to the cutter
frame. Abutting of the shaft on both sides of the oblong hole on the sliding blade guides the
sliding blade. The sliding blade spacer spring and sliding blade spring are attached to the
sliding blade shaft and are held to the cutter frame by the bush-nut (stopper ring). The sliding
blade link is rotatably supported on the sliding blade link shaft.  The scissors blade transmission
shaft mounted on the sliding blade and the scissors blade transmission shaft mounted on the
scissors blade abut the two oblong holes in the sliding blade link, thereby comprising the link
structure. Coupled with the reciprocal rotation of the scissors blade, the sliding blade moves
reciprocally in a direct linear direction.  When the scissors blade (and the sliding blade) is at its
idle position, the micro switch is OFF (open).

Clutch Mechanism

These parts and drive mechanisms can be damaged when foreign matter enters between the
movable blades (scissors blade and sliding blade) and the stationary blade. A power
transmission clutch has been established to protect these parts in the event that foreign matter
enters between the movable blades (scissors blade and sliding blade) and the stationary blade on
this printer. Sliding occurs between the autocutter deceleration gear and cutter worm gear and
the motor lock is held in check. If the cutter blades (scissors blade and sliding blade) do not
return within a predetermined amount of time, an error is detected to stop, cut the flow of
power to the motor, and enter a reverse rotation energizing of the motor to automatically
recover the movable blades (scissors blade and sliding blade).

Autocutter Operation

The following describes the order of operation of the autocutter.

1. Voltage is charged to the terminals of the cutter motor and the cutter motor gear rotates.

2. The cutter blade drive shaft moves the scissors blade toward the stationary blade.

3. The sliding blade, linked to the movement of the scissors blade, also moves toward the

stationary blade.

«
...
222
223
224
225
226
...
»

Содержание U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Отзывы:

Нет отзывов