manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Руководство по обслуживанию, Страница: 22 / 325

Поделиться
Скачать
Epson U675 - TM Color Dot-matrix Printer Скачать руководство пользователя страница 22

1-10

   Troubleshooting

Rev.D

Confidential

Roll paper cover open error

The roll paper cover 
(rear cover) was 
detected as open 
when printing.

Close the roll paper cover (rear cover).

Memory or gate array R/W error

The R/W check did 
not operate 
properly for the 
memory or the 
gate array.

Replace the main circuit board unit to see if the 
printer is repaired.    (See page 2-96.)

High voltage error

The power supply 
voltage is high.

Replace the power supply unit to see if the printer is 
repaired.    (See page C-4.)

Low voltage error

The power supply 
voltage is low

Replace the power supply unit to see if the printer is 
repaired.    (See page C-4.)

CPU execution error

An abnormal CPU 
operation was 
detected, or the I/F 
board is 
disconnected.

1. Check whether the I/F board is connected.

2. Replace the main circuit board unit to see if the 

printer is repaired.  (See page 2-96.)

Drive circuit error

One of the 
following was 
detected.

❏

Print head 
thermistor 
detection error

❏

Lever drive motor 
assembly error

1. Check if the printer is repaired after replacing the 

print head unit.  (See page 1-15.)

2. Check the resistance of the lever drive motor 

assembly.  (See page 1-11.)  Replace if shorted.

3. Check if the printer is repaired after replacing the 

lever motor T. P. detector assembly.  (See page 2-
78.)

4. Check if the printer is repaired after replacing the 

main circuit board unit.  (See page 2-96.)

Head high temperature error/roll 
paper error

One of the 
following problems 
has occurred.

❏

The roll paper 
has been 
inserted into the  
path wrong.

❏

The print head 
temperature is 
high.

1. If the error has occurred after loading the roll 

paper, the roll paper has been inserted into the 
path wrong.  Reinstall the roll paper.

2. If the error occurred during printing, a high head 

temperature has been detected.  This error may 
occur if you print continuously for too long.  Leave 
the printer as it is.  The error will be automatically 
cleared when the temperature has decreased.  If 
this error occurs frequently, check if the ambient 
temperature is within specifications. 

Table1-2 Error causes and solutions

Type of Error and ERROR LED Pattern

Explanation

Solutions 
(Listed in the order you should use to check printer)

Содержание U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Отзывы:

Нет отзывов