Epson U675 - TM Color Dot-matrix Printer Скачать руководство пользователя страница 187

Страница: 187 / 325

Rev.D

Installation Appendix C-3

TM-U675/U675P (with autocutter) Service Manual

Confidential

Connecting to a Direct Connection Display Module

WARNING:

Be sure not to connect this cable to the drawer kick-out connector, which is next to the
power connector.

Also do not connect a telephone line to the display module connector.

Note:

The DM connector can be used only with the serial interface model of this printer.

1. Make sure that the printer is turned off.

2. Plug the cable connector (provided with the direct connection display module) securely into

the printer's display module connector until it clicks.

Figure C-5 Connecting to a direct connection display module

DM connector

Содержание U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Результаты поиска

Содержание U675 - TM Color Dot-matrix Printer

Отзывы:

Бренды по названию

Популярные бренды

Epson U675 - TM Color Dot-matrix Printer, Руководство по обслуживанию

Результаты поиска

Содержание U675 - TM Color Dot-matrix Printer

Отзывы:

Бренды по названию

Популярные бренды