manualshive.com logo in svg

Epson U675 - TM Color Dot-matrix Printer, Руководство по обслуживанию

Поделиться
Скачать
Epson U675 - TM Color Dot-matrix Printer Скачать руководство пользователя страница 260

Appendix D-72

   Product Overview

Rev.D

Confidential

Important Parts

Fuses

Table D-16 Fuses

Fuse

Function

Standard

Fuse F1

Main fuse, provided for safety purposes.  Fuse may burn out 
when input circuit is unsafe.
Make sure to use the same type of fuse when it is replaced.  
Replace the fuse after eliminating the cause of the burn out.  
Burn out may lead to a malfunction.

R452003   Littelfuse Inc.

Fuse F2

Used to protect against unsafe circuit elements.  It will burn out in 
the event of a circuit board problem.  The problem cannot be 
corrected by replacing the fuse.
It may burn out due to an unsafe 24VC line.  Replace the fuse 
after eliminating the cause of the burn out.  Burn out may lead to 
a malfunction.

R451002   Littelfuse Inc.

Fuse F4

Used to protect against unsafe circuit elements.  It will burn out in 
the event of a circuit board problem.  The problem cannot be 
corrected by replacing the fuse.
Replace the fuse after eliminating the cause of the burn out.  
Burn out may lead to a malfunction.

ICP-S1.0   ROHM ELECTRONICS

Fuse F5

Located on power supply line of the interface board

R452003  Littelfuse inc

Fuse R3

Used as safety protection for the logic power source circuit.  It 
may burn out due to a logic power circuit problem or excessive 
VCC voltage.  Replace the fuse after eliminating the cause of 
the burn out.  Burn out may lead to a malfunction.

RF73B2HTD0.51OHMJ   KOA Corp.

Содержание U675 - TM Color Dot-matrix Printer






































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды