Epson LQ-2550 Скачать руководство пользователя страница 95

Страница: 95 / 301

REV.-A

2.3.2

I n t e r f a c e

This printer has both an 8-bit parallel interface and an RS-232C serial interface.

2.3.2.1 8-Bit Parallel Interface

Operating Principles

Figure 2-42 shows the 8-bit parallel interface data transmission timing. Data is transferred between

a host computer and the printer using the following sequence:

BUSY

DATA

STROBE

Figure 2-42. 8-Bit Parallel Data Transmission Timing

First, the host computer confirms that the BUSY signal from the printer is low or that the

signal from the printer is high. When the BUSY signal is low, the printer is ready to receive data.

When it is high, the printer can not receive data from the host computer since the printer is

data. Therefore, the host computer does not transfer data until the BUSY signal changes

from high to low. (Some host computers check both the BUSY and

signals, and others just

check either the BUSY or

signal.)

After the host computer has confirmed that the BUSY signal is low, it places data (8 bits per word)

in parallel on the data bus (DO - D7), and the printer reads the data

edge of the STROBE

pulse.

After receiving a data word from the host computer, the printer sets the BUSY signal high to inform

the host computer that the printer is

data and is not ready to receive any more data.

After

the data, the printer sets the

signal low, allowing the host computer to

transfer data again. The printer sets the BUSY signal low approximately 5

after setting the

signal low, then sets the

signal high after approximately 5

informing that the

host computer that the printer is ready to receive data.

2-48

Содержание LQ-2550














































































































































































































































































































Результаты поиска

Содержание LQ-2550

Отзывы:

Бренды по названию

Популярные бренды

Epson LQ-2550, Техническое руководство

Результаты поиска

Содержание LQ-2550

Отзывы:

Бренды по названию

Популярные бренды