Epson LQ-2550 Скачать руководство пользователя страница 180

Страница: 180 / 301

4.2.5.4 Cable Removal (Front Head

Rear Head

Color Select Cable)

W A R N I N G

●

When removing the cables from the two tabs of the carriage, be careful not to disconnect

the

three

should be put together as shown in Figure 4-28 for assembly.

. If they are put together incorrectly. the printer mechanism will not operate.

Fold front and rear head cables and put them together. Then mount them to the

carriage with rear head cable on top.

. . . . . Bind the three cables together and fold them.

Select Cable

Figure 4-28. Cable Binding

Step 1:

Step 2:

Step 3:

Step 4:

Step 5:

Step 6:

Step 7:

Step 8:

Step 9:

Cable

Remove the printer mechanism. (Refer to Section 4.2.5.1.)

Remove the printhead. (Refer to Section 4.2. 1.)

Remove the cartridge base. (Refer to Section 4.2.5.3.)

Remove cable holders A and B, then draw out the three cables, the front head cable, rear head

cable, and color select cable, from the cutout in the base frame.

Place the carriage over the cutout in the base frame, then disconnect the two connectors from

the back of the base frame.

Remove the color select unit. (Refer to Section 4.2.5.2.)

Loosen the three cables from the two tabs of the carriage.

Remove the screw

6) securing the color select cable, and remove the cable.

Remove the front and rear head cables.

Connector

Cable Holder

cutout

Figure 4-29. Cable Holder B and Connector

Removal (Back of Base Frame)

ASSEMBLY POINT:

Front Head Cable

Rear Head Cable

Tab

Color

Cable

-CPS

Figure 4-30. Front Head Cable, Rear Head

Cable, and Color Select Cable Removal

●

Verify that the cables do not touch the left frame or the back of the carriage when moving

the carriage to the left end.

4 - 1 8

Содержание LQ-2550














































































































































































































































































































Результаты поиска

Содержание LQ-2550

Отзывы:

Бренды по названию

Популярные бренды

Epson LQ-2550, Техническое руководство

Результаты поиска

Содержание LQ-2550

Отзывы:

Бренды по названию

Популярные бренды