manualshive.com logo in svg

Epson LQ-2550, Техническое руководство

Поделиться
Скачать
Epson LQ-2550 Скачать руководство пользователя страница 238

6.1 PREVENTIVE MAINTENANCE

Proper maintenance is essential to maintain optimal printer performance for the longest possibly period

and to minimize malfunction frequency. Preventive maintenance includes regular cleaning of the case

exterior, using neutral detergent, and occasional vacuuming of the mechanism interior to remove dust

and paper particles.

Following cleaning, refer to Section 6.2 to verify that the unit is adequately lubricated. Before returning

the serviced printer to the consumer, inspect the springs, paper feed rollers, and the basic operationof

the unit.

W A R N I N G

Disconnect the printer from the power supply before performing maintenance. Do not use thinner,

 or ketone-based solvents on 

 components of the printer.

6.2 

LUBRICATION AND ADHESIVE APPLICATION

EPSON recommends that the points illustrated in Figures 6-2, 6-3, and 6-4 be lubricated, according

to the schedule listed in Table 6-2, with EPSON O-2, G-2 and G-27, which have been extensively tested

and found to comply with needs of this priter. (Refer to Table 6-1 for details of O-2, G-2 and G-27.) Be

sure that the parts to be lubricated are clean before applying lubricant, and avoid excessive application,

which may damage related parts.

Adhesive application is necessary at the point indicated in Table 6-3 when the part is disassembled

or replaced. EPSON recommends 

 Lock #2 (G) adhesive be applied to the point diagramed in

Figure 6-3. Avoid overflow of excess to related parts.

Table 6-1. Lubricants and Adhesive

Classification

Designation

Capacity

Availability

Part No.

Oil

o-2

40 cc

B7 10200001

Grease

G-2

40 g

B70020001 1

Grease

G-27

40 g

B702700001

—

Adhesive

 

 

 #2 (G)

1000 g

B 7 3 0 2 0 0 2 0 0

 EpSON exclusive 

product

Table 6-2. Lubrication Points

(Refer to Figures 6-2, 6-3, and 6-4.)

Ref. No.

(1)
(2)

(4)
(5)X
(6)
(7)

(9)
(1 o)

Lubrication Points

Oil pad inside of carriage
Gear portion of platen gear
Contact portion of dowel on release trigger plate and right frame
Gear portion of release planetary gear
Four convex portion of release sun gear
Gear portion of tractor transmission gear
Outer gear portion of paper feed reduction gear

Contact portion of paper release support lever and paper release lever
Outer and inner gear portions of loading gear 

A

Outer and inner gear portions of loading gear assembly

Lubricant

o-2 “
G-27
G-2
G-27

G-27
G-27
G-27
G-27
G-27
G-27

 Lubrication is necessary in the process of assembly

6-1

Содержание LQ-2550














































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды