Do not perform reverse feeding for more than 1/6 “.
Because accuracy of paper feed cannot be assured, do not perform reverse feeding
after the paper end has been detected.
b) When using pull tractor feed :
Adjust the paper release lever at front position.
Remove the paper tension unit and mount the pull tractor unit.
Use the paper path when a single sheet is inserted.
c) ‘A’’---
“
-’‘“ ‘---”-”
“
WV I
.
Adjust the paper release lever at front position.
Remove the paper tension unit and mount the pull tractor unit.
Do not loosen the paper between the platen and the pull sprocket.
Precisely the horizontal position of the pull sprocket and push tractor.
Do not perform reverse feeding for more than 1/6”.
Do not perform reverse feeding after the paper end has been detected.
Paper Loading Directions
Inserted from the rear side
Line Spacing
1/6” or programmable (min. 1/360”)
Line Feed Speed
See Table 1-3.
Table 1-3. Line Feed Speeds
1 /6” line spacing
Feeding Method
I
Continuous
[ins/line]
Friction without
56.4
Friction with
67.3
3.1
Tractor
I
64.1
I
Paper specifications
Cut sheet paper
Refer to
1-4.
Table 1-4. Cut Sheet Paper Specified Conditions
LQ-106O
1
182-257 (7.2 -10.1 “)
182-364 (7.2- 14.3”)
182-364 (7.2-14.3”)
0.065-0.10 (0.0025-0.004”)
14-22 (52-82
Quality
Plain paper
Copies
Not available
1-4
Содержание LQ-1060
