Epson Equity III Скачать руководство пользователя страница 86

Страница: 86 / 103

EPSON

EPSON AMERICA, INC.

SERVICE

RODUCT

UPPORT

ULLETIN

PSB NO.: S-0017A

DATE: 6/29/88

PAGE:

1 of

SUBJECT:

EQUITY COMPUTERS AND FLOPPY

DISK DRIVES

There is still some

confusion regarding which

FDDs will work

with which Equity. Here is a quick reference for FDD selection

(for detailed information, refer to PSB Number S-0001).

Equity

--- --

Equity

I+

--- ---

Epson Q520A-AA (360

Epson Q213A-AA (360 KB)

Epson A112A-AA (720 KB, 3.5")

Equity

--- ---

Epson Q213A-AA (360 KB)

Epson Q911A-AA (1.2 MB)

Equity

II+

--- ----

Epson Q213A-AA (360 KB)

Epson Q212A-AA (1.2 MB)

Epson A112A-AA (720 KB, 3.5")

Equity

III

--- ----

Epson Q213A-AA (360 KB)

Epson Q212A-AA (1.2 MB)

Equity

III+

--- -----

Epson Q213A-AA (360 KB)

Epson Q212A-AA (1.2 MB)

Epson A112A-AA (720 KB, 3.5")

1 -

This is the only FDD compatible with the Equity

2 - This is the only 1.2 MB FDD compatible with the Equity

II.

One of the key issues is: NEVER USE ANY 1.2 MB FDD OTHER THAN

THE Q911A-AA IN THE EQUITY II!

The interface

is slightly

different from the AT "standard". As a result,

an AT-type

drive will work erratically (if at all). One of the problems

is a disk change error,

or continuing to use

the directory

from a previous disk.

Also on the Equity

II,

MS-DOS 3.2 does not allow sufficient

retries on diskette read/write with the Q911A-AA.

Consistent

"Abort, retry, ignore?"

messages

result

when attempting to

log a new disk.

Typically, "r" for

retry will overcome this

situation. MS-DOS 3.2 operation with the Q213A-AA is correct.

EPSON AMERICA SERVICE, 23610 TEL0 AVENUE, TORRANCE, CALIF. 90505

Содержание Equity III








































































































Результаты поиска

Содержание Equity III

Отзывы:

Epson Equity III, Информационный бюллетень по поддержке продукции, Страница: 86 / 103

Результаты поиска

Содержание Equity III

Отзывы: