Epson Equity III Скачать руководство пользователя страница 28

Страница: 28 / 103

EPSON

EPSON AMERICA, INC.

SERVICE

PSB NO.:

S-0061

DATE: 10/12/88 ORIGINATOR: MWT PAGE:

of 13

SUBJECT: NOVELL NETWARE CERTIFICATION

WITH SERIES

COMPUTERS

The purpose of this bulletin is to provide information regarding

compatibility between the Epson Equity series computers and

Novell local-area networking products. This information was

provided to Epson by Novell's Independent Product Testing group,

a part of their Services Division. The Independent Product Test

(IPT) reports are available to Novell authorized dealers. The

IPT numbers are as follows:

Equity

I+:

IPT

1029

Equity

II+ (10

MHz):

IPT 1030

Equity

III+ (10

MHz):

I P T 1 0 4 8

Equity

III+ (12

MHz):

IPT 1082

Please contact your Novell representative to obtain these reports

as required.

Definition of Terms

DCB

Disk coprocessor board

DIB

SCSI

Disk interface board

INIC

Intelligent network interface card

LAN

Local-area network

ND286

Non-dedicated Advanced NetWare 286

NIC

Network interface card

SCSI

Small Computer System Interface

Testing Information

The following tests were conducted on the Equity

I+, II+

and

III+

computer products:

NetWare Operating System Functionality: Dedicated and

non-dedicated file server tests are performed.

Network

Interface

Card Compatibility: All network cards supported

by the tested release of NetWare are tested.

Operating System Network Driver Compatibility: All supported

network cards are tested with a NetWare driver designed

specifically for each card. To test accessibility of the driver

to the interface card, a workstation is attached and logged into

the file server and run through a series of NetWare and MS-DOS

commands.

EPSON AMERICA SERVICE, 23610 TEL0 AVENUE, TORRANCE, CALIF. 90505

Содержание Equity III








































































































Результаты поиска

Содержание Equity III

Отзывы:

Похожие инструкции для Equity III

Бренды по названию

Популярные бренды

Epson Equity III, Информационный бюллетень по поддержке продукции

Результаты поиска

Содержание Equity III

Отзывы:

Похожие инструкции для Equity III

Бренды по названию

Популярные бренды