manualshive.com logo in svg

Epson Equity III, Информационный бюллетень по поддержке продукции, Страница: 39 / 103

Поделиться
Скачать
Epson Equity III Скачать руководство пользователя страница 39

NUMBER:

S-0061

PAGE: 12  of 13

Configurations tested with Advanced NetWare 286 2.0a

NetWare driver configuration for dial-in remote access:

NETWARE DRIVER CONFIGURATIONS

STATUS

SMC/PD Arcnet:

Passed

ASYNC:

Passed

Configurations tested with Advanced NetWare 286 2.0a

NETWARE DRIVER CONFIGURATIONS

STATUS

Etherlink Plus (3C505\2012):

Passed

Configurations tested with ELS NetWare 286 Level I 2.0a

NETWARE DRIVER 

CONFIGURATIONS

STATUS

Novell Ethernet (NE1000):

Passed

Configurations tested with SFT NetWare 

286 

Level 

I/II 2.0a

NetWare Utilities

PREPARE:

Passed

INSTALL:

Passed

NETWARE  DRIVER CONFIGURATIONS

STATUS

Etherlink Plus (3C505\2012)

Passed

Comments: The 

III+ 

(12 MHz) will not function correctly at

12 MHz with the Novell DCB; however, it will function correctly

at 8 MHz with the DCB.

Configurations tested with SFT NetWare 286 Level 

II 2.1

NetWare Utilities

NETGEN:

Passed

NETWARE  DRIVER CONFIGURATIONS

STATUS

Etherlink Plus (3C505\1194):

Etherlink Plus (3C505\2012):

Etherlink (3C501):

Novell Ethernet (NE1000):

 Micom (NP600):

Passed

Passed

Passed

Passed

Passed

Содержание Equity III








































































































Отзывы:

Нет отзывов