EPAK-TV TV44, Руководство пользователя

Страница: 9 / 70

16
English English
17
7. The display shows
FastScan
. Press

to go to
LNB Type
. Press

to select.
8. The display will show the standard setting lin 0 which is valid for Europe. By pressing the
 key you can change the LNB settings. Press  to select. The display will return to: LNB
Type .
☛ The standard setting lin 0 is the only one supported by a standard system. Reception from
satellites with a rotated skew will require an optional LNB mounting with variable skew (see
Appendix E). Reception from circular polarized satellites will require a circular LNB type.
9. Press  repeatedly until the legend Comp Cal appears. Press  to select.
☛ The calibration of the compass must be carried out in the harbor in calm waters! If the mount-
ing surface of the antenna unit changes, or if the superstructures in the vicinity of the antenna
unit are modified, the calibration has to be done again! See also section 6.1.
10. The display interchanges between the legends: Compass and UpDate? . Press  to
calibrate.
11. The display interchanges between the legends:
Compass
and
calibrat
and then
checking until the legend complete is shown for a brief moment, and then returns to
Comp Cal
, which indicates that the calibration of the compass is completed.
12. Press  to go to quit , and press  to confirm.
The system is now adjusted to surrounding conditions and is ready to search for satellites to be
stored.
4 TV operation
Press the power key to turn on the control unit. The display shows Init for initialization. After
the initialization is completed, the display interchanges between scanning and Sat X (X
is the last shown storage position) until the satellite has been located. The system will now run a
check on the satellite:
checking . If o.k., the display will briefly indicate complete and
then return to Sat X.
The antenna will maintain its connection to the satellite even when the boat is moving. (Providing
that the tracking function is active, see section 3.5).
If you wish to select a different satellite, press
 repeatedly until the desired satellite position
appears, and then confirm with  .
☛
If no satellites are stored, the display will show Setup (flashing). You are now back in the
main menu and can add new satellites (see sec. 5.1).
If the search for a new satellite takes more than 1 minute, even though there is a clear view to the
satellite, or if, after several times finding the right satellite, the display shows
upd reco and
interchanging with the actual satellite number, then the satellite data base has to be updated, see
section 5.2.
If there is no picture on the TV after the satellite has been checked and found o.k., there are two
possibilities:
1. The satellite service provider has changed the transponders or it is the wrong satellite. In order
to proof the right satellite has been found, try to switch to other programs on the receiver. If all
other programs are in their usual places, you need to reprogram your receiver for the program
which have changed. Please refer to the manual of the receiver.
2. US only: In case that no program can be received, try to turn off the Fastscan function, see
section 6.4.
When changes are made, return to Sat X and press  to start a new search.
If the search for a new satellite takes longer than 4 minutes and after some time the display shows
Sat ok? , then the requested satellite could not be found. All available satellites will be pre-
sented and the operator can choose one.
Make sure the receiver is switched to a program from this satellite, so the correct satellite can
be identified. If the display shows
Sat ok? and there is no picture on the TV, press  to
continue the search.This has to be repeated, until the TV shows the correct program. Press  to
confirm.
The display will now interchange between
Sat
X and
UpDate?
. Press

to update the sat-
ellite data base. The display will flash: updating , and shortly after: checking , and then:
complete
. The display will now return to
Sat
X and the requested program will appear on
the TV. If the display interchanges between scanning and complete during the search,
no suitable satellite could be found. Press

to go to the main menu and the display will flash
Setup .