enware ENMATIC 5000 SERIES Скачать руководство пользователя страница 5

Страница: 5 / 16

www.enware.com.au

Call 1300 369 273

INSTALLATION

BEFORE PROCEEDING WITH INSTALLATION

SELECT THE LOCATION OF THE SENSOR
When selecting a location to install the

wall-mounted sensor, consider the following:
• Ease of operation
• Water splash / water drips
• Passing traffic

Be sure that passing traffic cannot trigger

the sensor. Allow at least 400mm clearance

between sensor and passing traffic.

• Obstructions

Ensure that nothing is within range of the

sensor. Any obstruction directly in front of, and

within possible range of, the sensor can trigger

the sensor randomly or constantly turn it on.

• Reflections and Lighting

If the sensor unit is installed into a location

where a nearby wall or object is reflecting

the Infrared light back, the unit is effectively

blinded and will not operate. Up to 600mm

clearance may be necessary from reflective

surfaces, such as ceramic tiles and stainless

steel, directly in front of, and parallel to, the

front face of the sensor. Any bright lighting

reflecting off a highly reflective surface such

as a stainless steel sink, or a high visibility

reflective vest, may also interfere with correct

sensor operation.

SET-OUT HEIGHTS
Suggested heights from finished floor:

Spout Oulet

1050 mm
1120mm to point of water

discharge

(Australasian Health Facility

Guidelines)

Top of

Basin

850 mm
865mm (Australasian Health

Facility Guidelines)
800 - 830mm

(refrerence: AS1428.1-2009)

Содержание ENMATIC 5000 SERIES

















Результаты поиска

Содержание ENMATIC 5000 SERIES

Отзывы:

Похожие инструкции для ENMATIC 5000 SERIES

Бренды по названию

Популярные бренды

enware ENMATIC 5000 SERIES, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ENMATIC 5000 SERIES

Отзывы:

Похожие инструкции для ENMATIC 5000 SERIES

Бренды по названию

Популярные бренды