background image

Call 1300 369 273 

www.enware.com.au

TECHNICAL DATA

Inlet Connection

15 mm (1/2”) BSP

Recommended Working Pres-
sure

100 - 500 kPa*

Flow Rate

4 star (7.7 lpm)water efficiency rating supplied standard.
6 Star (5.6 lpm) or 3 star (9.1 lpm) WELS ratings available on 
request

Maximum Hot Water Supply 
Temperature

70°C^

Operating Voltage

24V AC

Power Consumption

Less than 9W

Cable Lengths

Transformer with 2m Lead to Sensor, 
1.8m Lead from Sensor to Solenoid
Sensor Cable Length 0.1m

Sensor Functions

Wave-On Wave-off, Time flow

Time-out settings for  
Wave-On Wave-Off

15, 30, 45, 60 seconds  
(Factory set at 45 sec)

Run time settings for Time 
Flow

6, 9, 12, 15 seconds  
(Factory set at 6 sec)

a)  45°C  for  healthcare  and  aged  care  buildings, 

early childhood centres, primary and secondary 

schools  and  nursing  homes,  or  similar  facilities 

for  the  aged,  the  sick,  children,  or  people  with 

disabilities; and

b) 50°C for all other situations
(Laundries and kitchen sinks are not required to 

have heated water at a maximum of 50°C)

*Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and 

AS/NZS3500.  Installations  not  complying  with  PCA  and  AS/NZS  3500  may  void  the  product  and 

performance warranty provisions.
Reference should also be made to the Australasian Health facility Guidelines (AHFG), ABCB and Local 

Government regulations when considering the choice of, and the installation of these products.
^ All heated water installations for sanitary fixtures used primarily for personal hygiene purposes shall 

deliver heated water at a temperature not exceeding:

This product must be installed and commissioned by a qualified plumber.
For use with potable water only.
NOTE: Enware Australia advises: 
1. Due to ongoing Research and Development, specifications may change without notice. 
2. Component specifications may change on some export models.

The more

stars the more

water efficient

6

litres per

minute

WATER RATING

www.waterrating.gov.au

The more

stars the more

water efficient

8

litres per

minute

WATER RATING

www.waterrating.gov.au

The more

stars the more

water efficient

9.5

    litres per

    minute

WATER RATING

www.waterrating.gov.au

Содержание ENMATIC 5000 SERIES

















Отзывы: