Enviro E20 Скачать руководство пользователя страница 1

Страница: 1 / 40

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

50-2261

Massachusetts installations (Warning): This product must be installed by a licensed plumber or gas fitter

when installed within the Commonwealth of Massachusetts. Other Massachusetts code requirements:

Flexible connector must not be longer than 36in., a shut off valve must be installed; only direct vent

sealed combustion products are approved for bedrooms/bathrooms. A carbon monoxide detector

is required in all rooms containing gas fired direct vent appliances. The fireplace damper must be

removed or welded in the open position prior to installation of a fireplace insert.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified

kit is used.

WHAT TO DO IF YOU SMELL GAS

• Open windows/extinguish any open

flame.

• Do not try to light any appliance.

• Do not touch any electrical switch

or use any phone in your building.

• Immediately call your gas supplier

from a neighbour’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas

supplier, call the fire department.

WARNING:

If the information in this manual

is not followed exactly, a fire or explosion

may result causing property damage, personal

injury or loss of life. Installation and service

must be performed by a qualified installer,

service agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vapours and liquids in the vicinity of this or any

other appliance.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

OWNERS MANUAL

E20

Gas Insert

WARRANTY

REGISTRA

TION

enviro.com/warranty

Содержание E20









































Результаты поиска

Содержание E20

Отзывы:

Похожие инструкции для E20

Бренды по названию

Популярные бренды

Enviro E20, Руководство пользователя

Результаты поиска

Содержание E20

Отзывы:

Похожие инструкции для E20

Бренды по названию

Популярные бренды