Entrematic LCU30H Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 42

Entrematic LCU30H Скачать руководство пользователя страница 9

9

IP2251EN

The procedure to switch on the display is as follows:

• press the ENTER key

• the display functioning check starts

• the ﬁrst level menu is displayed

The procedure to switch off the display is as follows:

• press the ESC key

NB: the display switches off automatically after 60 s of inactivity.

• The simultaneous pressing of the ↑and ENTER keys produces an opening com-

mand.

• The simultaneous pressing of the ↓and ENTER keys produces a closing command.

• The simultaneous pressing of the ↑ and ↓ keys produces a POWER RESET com-

mand (power supply interruption and automation restart).

• Keep the UP ↑ or DOWN ↓ key pressed to begin fast menu scrolling.

• In some menus, the parameter measurement unit can be viewed by pressing the

ENTER key once the value has been displayed.

Example: setting of 10 seconds for parameter OB.

5. Programming

5.1 Switching the display ON and OFF

i

NB: pressure on the keys may be quick (less than 2 s) or prolonged (longer than 2 s).
Unless speciﬁed otherwise, quick pressure is intended.
To conﬁrm the setting of a parameter, prolonged pressing is necessary.

5.2 Navigation

keys

«
...
7
8
9
10
11
...
»

Содержание LCU30H











































Отзывы:

Нет отзывов