manualshive.com logo in svg

Entrematic LCU30H, Руководство по установке, Страница: 41 / 42

Поделиться
Скачать
Entrematic LCU30H Скачать руководство пользователя страница 41

41

IP2251EN

13. Troubleshooting

Problem

Possible cause

Alarm sig-

nalling

Operation

The control panel 
does not switch on

No power supply.

Check the power supply cable and the 
relative wiring

Overload on output 0-1

Disconnect any loads connected to ter-
minal 1

The automation 
does not open or 
close.

No power.

Check power supply cable.

Short circuited accessories

Disconnect all accessories from ter-
minals 0-1 (a voltage of 24V= must be 
present) and reconnect them one at a 
time.
Contact Technical Service

Blown line fuse.

Replace fuse.

Safety contacts are open.

  

Check that the safety contacts are closed 
correctly (NC).

Safety contacts not correctly 
connected or self-controlled 
safety edge not functioning 
correctly. 

   Check connections to terminals 6-8 on 

control panel and connections to the 
self-controlled safety edge.

Photocells activated.

  

Check that the photocells are clean and 
operating correctly.

The automatic closure does 
not work.

Issue any command. If the problem per-
sists, contact Technical Service

Motor fault

Check motor connection, if the problem 
persists, contact Technical Service.

The external safety 
devices are not ac-
tivated.

Incorrect connections be-
tween the photocells and the 
control panel.

 

Check that 

  / 

 is displayed

Connect NC safety contacts together in 
series and remove any jumpers on the 
control panel terminal board.

Check the 

 

 → 

    and   

 → 

 setting 

The automation 
o p e n s / c l o s e s 
briefly and then 
stops. 

There is a presence of friction.

Manually check that the automation 
moves freely and check the 

 / 

 

adjustment
Contact Technical Service

The remote control 
has limited range 
and does not work 
with the auto-
mation moving.

The radio transmission is im-
peded by metal structures and 
reinforced concrete walls.

Install the antenna outside. 

Replace the transmitter batteries.

The remote control 
does not work

No storage module or incor-
rect storage module.

Switch the automation off and plug in the 
correct storage module.

Check the correct memorisation of the 
transmitters on the built-in radio. If there 
is a fault with the radio receiver that is 
built into the control panel, the remote 
control codes can be read by removing 
the storage module.

Содержание LCU30H











































Отзывы:

Нет отзывов