background image

 

 

0

T≤2 

10 

-3.2 

-2

T≤0 

15 

-5.4 

-4

T≤-2 

20 

-7.8 

-7

T≤-4 

25 

-10.7 

-11

T≤-7 

30 

-14.1 

-14

T≤-11 

35 

-17.9 

-19

T≤-14 

40 

-22.3 

-24

T≤-19 

45 

-27.5 

-31

T≤-24 

50 

-33.8 

-31

T≤-29 

60 

-34.7 

Remarks:  The  mass  percentage  concentration  C%=the  mass  of  the  solute/the  ma

ss  of  the 

solution. The example shows that the historically lowest ambient temperature in Shanghai, China is 

-12.1

.  Check  the  table  above,  and  45kg  of  glycerol  should  be  added  to  the  100kg  antifreeze 

mixture  as  antifreeze,  or  100kg  of  antifreeze  mixture  needs  to  add  40kg  of  ethylene  glycol  as 

antifreeze. 

 

2.  Trouble shooting 

Phenomenon 

Reasons 

Solutions 

The unit doesn’t work. 

1.No power supply. 

1.Please wait for the power supply. 

2.Power switch not on. 

2.Open up the power switch. 

3.Power switch fuse blown. 

3.Replace fuse. 

4.The timing time is not up. 

4.Please wait or cancel the timing settings. 

The unit does not work 

when turns on. 

1.Compressor protection interval not 

reached. 

1.Please wait the protection time to end patiently. 

2.The unit water temperature does not reach 

the starting water temperature. 

2.It is normal phenomenon, wait for the starting 

water temperature. 

The unit works 

normally, but the hot 

water temperature is 

low. 

1.Improper temperature setting. 

1.Set proper temperature. 

2.Excessive hot water consumption. 

2.Wait the hot water to warm up before using it. 

3.The air inlet or outlet of outdoor unit or 

indoor unit is blocked. 

3.Remove the obstruction from the air inlet or 

outlet. 

The unit turns on 

automatically. 

1.The timing time is up. 

1.If you do not want to use it, please turn off the 

unit or cancel the timing settings. 

Abnormal sound of the 

unit. 

1.There is too much dust or obstruction on 

the air inlet of the unit evaporator, produce 

strong and weak sound of wind. 

1.Remove the dust or obstructions from the unit 

evaporator. 

2.The Refrigerant flow may produce some 

noise when the unit turns on or turns off. 

2.It is normal phenomenon. 

3.No power on,    the unit rings like 'dada'    .  3.It is normal phenomenon, reset of EEV. 

 

Содержание BC-F20HWR2-200L


































Отзывы: