manualshive.com logo in svg

enertexbayern Enertex KNX Smartmeter 85A (RT), Руководство и настройка, Страница: 65 / 69

Поделиться
Скачать
enertexbayern Enertex KNX Smartmeter 85A (RT) Скачать руководство пользователя страница 65

Handbuch-KnxSmartmeter-85A-en-3.odt, 2018-10-04                                             

Seite 65 von 69 

ID

Name

Object function

Length

Type

Flags

130 Intermediate 

counter 4

Cost counter-current value

4 Byte

[13.001]
DPT_Value_4_Cou
nt

CR-T-

This  object contains the current cost counter value of the intermediate counter in ct. The counter value may be 
positive or negative. The value of the group object is respectively copied after the lapse of the counting interval into 
the group object “Cost counter - previous value” and then reset.

ID

Name

Object function

Length

Type

Flags

131 Intermediate 

counter 4

Cost counter-previous value.

4 Byte

[[13.001]
DPT_Value_4_Cou
nt

CR-T-

The object contains  the cost counter value  from  the  previous  count  interval of  the  intermediate counter in ct.  If 
configured, this value is transmitted on the bus after its update. When transmitting the parameter “General - Offset  
when transmitting of intermediate counter values in (s)” operates as a transmission delay.

ID

Name

Object function

Length

Type

Flags

132 Intermediate 

counter 4

Limit message

1-Bit

[1.002]
DPT_Bool

C--T-

Group object that transmits the value 1 or 0, if the limit of the intermediate counter has been exceeded or fallen 
below.

ID

Name

Object function

Length

Type

Flags

133 Intermediate 

counter 4

External energy counter limit

4 Byte

[13.010]
DPT_ActiveEnergy

CR-T-

When writing to this object the limit is adopted from the bus. If the parameter “Adopt limit value from the bus” is set on  
“flighty” then the value adopted by the bus is discarded after the next reset of the intermediate counter. If in contrast  
the parameter is set on “permanent” then the limit adopted by the bus is permanent.

ID

Name

Object function

Length

Type

Flags

134 Intermediate 

counter 4

External cost counter limit 

4 Byte

[13.001]
DPT_Value_4_Cou
nt

CR-T-

When writing to this object the limit is adopted from the bus. If the parameter “Adopt limit value from the bus” is set on  
“flighty” then the value adopted by the bus is discarded after the next reset of the intermediate counter. If in contrast  
the parameter is set on “permanent” then the limit adopted by the bus is permanent.

ID

Name

Object function

Length

Type

Flags

135 Intermediate 

counter 4

Reset counter value

1-Bit

[1.017]
DPT_Trigger

C-W--

If   the   value  1  is   transmitted  to   this   object,   then  the  intermediate  counter  behaves   as  it   reaches  a  time   interval 
boundary. The group object is released by the parameter selection “Count interval - by trigger object”. See also 
section Intermediate Counter.

ID

Name

Object function

Length

Type

Flags

136 Intermediate 

counter 5

Energy counter-current value

4 Byte

[13.010]
DPT_ActiveEnergy

CR-T-

The object contains the current energy counter value of the intermediate counter in Wh. The counter value can be  
positive or negative. The value of the group object is respectively copied after the lapse of the counting interval into 
the group object “Energy counter - previous value” and then reset.

ID

Name

Object function

Length

Type

Flags

137 Intermediate 

counter 5

Energy counter-previous value.

4 Byte

[13.010]
DPT_ActiveEnergy

CR-T-

The object contains the energy counter value from the previous count interval of the intermediate counter in Wh. If 
configured, this value is transmitted on the bus after its update. When transmitting the parameter “General - Offset  
when transmitting of intermediate counter values in (s)” operates as a transmission delay.

Enertex

®

 Bayern GmbH – Ebermannstädter Straße 8 - 91301 Forchheim - Deutschland - [email protected]

Содержание Enertex KNX Smartmeter 85A (RT)






































































Отзывы:

Нет отзывов