enertexbayern Enertex KNX Smartmeter 85A (RT) Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 69

enertexbayern Enertex KNX Smartmeter 85A (RT) Скачать руководство пользователя страница 19

Handbuch-KnxSmartmeter-85A-en-3.odt, 2018-10-04

Seite 19 von 69

released. Since in this example only the three-phase consumption and its costs are to be

visualized, only the energy counter “Energy counter - three-phase”, the cost counter “tariff costs
counter 1” and “Tariff costs counter 2” are released. Furthermore 3 intermediate counter are

required to represent the energy consumption, the energy supply and the balancing energy over
the course of one day on the bus. Two other intermediate counter are used to represent the

daily energy supply costs and the daily compensation for electricity fed into the grid:

Figure 16: Settings „Energy counter/Tariff cost counter“ Example 2

In the following two tabs “Energy counter - three-phase” and “Tariff cost counter - three-phase”
no settings have to be made. Here the default values are used.

In the tab “Intermediate counter 1” the energy counter is configured to count the energy delivery.
For this purpose the “Input count value of the intermediate counter” has to be set to “Active

energy counter (consumption) - three-phase”. The count interval is set to “15min”. Furthermore
the setting “Transmit counter value before resetting” is enabled:

Figure 17: Setting „Intermediate counter 1“ Example 2

With this configuration the intermediate counter sums up the delivery of three-phase energy, that
is only the energy flux in positive power flux direction, each about 15 minutes and transmits this

sum on the bus at the end of the interval. After that the intermediate counter resets and starts

Enertex

®

Bayern GmbH – Ebermannstädter Straße 8 - 91301 Forchheim - Deutschland - [email protected]

«
...
17
18
19
20
21
...
»

Содержание Enertex KNX Smartmeter 85A (RT)






































































Отзывы:

Нет отзывов