Enertech ZS. Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 89

Enertech ZS. Скачать руководство пользователя страница 78

78

Enertech Global

IOM, ZS/ZT Models

Performance Check
Heat of Extraction(HE)/Rejection(HR)
Record information on the Unit Start-up Form

Equipment should be in full load operation for
a minimum of 10 minutes in either mode – WITH

THE HOT WATER GENERATOR TURNED OFF.

1. Determine flow rate in gallons per minute
•  Check entering water temperature
•  Check entering water pressure
•  Check leaving water pressure

Once this information is recorded,
• Find corresponding entering water

temperature column in the HE/HR Table.

• Find pressure differential in PSI column.
• Then read the GPM column to determine

flow in GPM.

2. Check leaving water temperature of unit.
• FORMULA: GPM x water temp diff. x 485

(antifreeze) or 500 (fresh water) = HE or HR in
BTU/HR

A 10% variance from table is allowed. Always
use the same pressure gauge & temperature
measuring device. Water flow must be in range
of table. If system has too much water flow,
performance problems should be expected.
Select the topic for your maintenance need.
Scan the QR code to access the video. Follow
the directions and tips provided to make the
project easier to complete.

Installation or Troubleshooting Tip Videos QR

Codes

ECM Temporary Replacement

ECM Motor Troubleshooting

Troubleshooting a TXV

Compressor Troubleshooting

Variable Speed Flow Centers

Return Conversion for and XT or CT

Heat Of Extraction and Rejection

Measuring Subcooling/Superheat

Nitrogen Purge While Brazing

Leak Testing an Air Coil

Loop Flushing

Repairing a Microchannel Air Coil

Testing a Coaxial Heat Exchanger

Troubleshooting a TXV

Installing a YT Vertical Unit

SECTION 12: TROUBLESHOOTING

«
...
76
77
78
79
80
...
»

Содержание ZS.


























































































Отзывы:

Нет отзывов