Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

94

Hauser

3.5

Parameters of the "Display" Transducer Block

The following table shows all the Hauser-specific parameters of the "Display" Transducer
Block. These can only be changed after entering an enabling code in the "Access - Code"
parameter.

!

Note!
FOUNDATION Fieldbus parameters are described in the "FOUNDATION Fieldbus Overview"
Operating Instructions (BA013S) (available at:

→

www.endress.com

→

Download).

"Display" Transducer Block/base index 1800:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

Access - Code

AUTO - OOS

All data of the measuring system are protected against inadvertent change.
Only when the code has been entered in this parameter can the
manufacturer-specific parameters be programmed and the device
configuration modified.

You can enable programming by entering:
• Code 55 (factory setting)
• Private code (

User input:

Max. 4-digit number (0 to 9999)

!

Note!

• If the write protection is enabled then access to the manufacturer-

specific parameters is blocked even if the right code is entered. Write
protection can be activated and deactivated by means of jumpers on the
I/O board (

→

see Operating Instructions for Proline Promag 55

FOUNDATION Fieldbus).

• You can disable programming again by entering any number (other than

the access code) in this parameter.

• The Hauser service organization can be of assistance if you

lose your private code.

• Certain parameters are not accessible unless a special service code is

entered. This service code is known only to the Hauser service
organization. Please contact your Hauser service center if you
require clarification.

• The entry made here does not affect the local display. Thus,

programming via the function matrix must be enabled separately.

Access - Status

read only

Use this parameter to display the current status of the possibilities for
accessing the manufacturer-specific parameters of the device.

User interface:

• LOCKED (parameterization disabled)
• ACCESS CUSTOMER (parameterization enabled)
• ACCESS SERVICE (parameterization enabled, access to service level)

Access - Code
Counter

read only

Displays how often the customer code, service code or the digit "0"
(code free) has been entered to gain access to the function matrix.

User interface:

Max. 7-digit number: 0 to 9999999

Factory setting:

0

«
...
92
93
94
95
96
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 40

Бренд: DataSafe Страницы: 4

Бренд: 1byone Страницы: 9

Бренд: hager Страницы: 4

Бренд: babymoov Страницы: 12

Бренд: BabyOno Страницы: 24

Бренд: babymoov Страницы: 4

Бренд: Daikin Страницы: 6

Бренд: C&D Technologies Страницы: 5

Бренд: Labelmate Страницы: 2

Бренд: Labnet Страницы: 2

Бренд: Tait Страницы: 46

Бренд: Tait Страницы: 9

Бренд: Tait Страницы: 89

Бренд: Tait Страницы: 20

Бренд: Tait Страницы: 10

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды