Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

90

Hauser

3.4

Parameters of the "Diagnosis" Transducer Block

The following table shows all the Hauser-specific parameters of the "Diagnosis" Transducer
Block. These can only be changed after entering an enabling code in the "Access - Code" parameter.

!

Note!
FOUNDATION Fieldbus parameters are described in the "FOUNDATION Fieldbus Overview"
Operating Instructions (BA013S) (available at:

→

www.endress.com

→

Download).

"Diagnosis" Transducer Block/base index 1600

Parameter

Write access with

operating mode

(MODE_BLK)

Description

Diag. -
Act. Sys. Condition

read only

Displays the current system status.

!

Note!

An exact error description as well as information on rectifying errors can
be found in the Operating Instructions for Proline Promag 55
FOUNDATION Fieldbus (BA126D).

Diag. -
Prev. Sys. Condition

read only

Displays the last error message that occurred.

Access - Code

AUTO - OOS

All data of the measuring system are protected against inadvertent change.
Only when the code has been entered in this parameter can the
manufacturer-specific parameters be programmed and the device
configuration modified.

You can enable programming by entering:
• Code 55 (factory setting)
• Private code (

User input:

Max. 4-digit number (0 to 9999)

!

Note!

• If the write protection is enabled then access to the manufacturer-

specific parameters is blocked even if the right code is entered. Write
protection can be activated and deactivated by means of jumpers on the
I/O board (

→

see Operating Instructions for Proline Promag 55

FOUNDATION Fieldbus, BA126D).

• You can disable programming again by entering any number (other than

the access code) in this parameter.

• The Hauser service organization can be of assistance if you

mislay your private code.

• Certain parameters are not accessible unless a special

service code is entered. This service code is known only to the
Hauser service organization. Please contact your
Hauser service center if you require clarification.

• The entry made here does not affect the local display. Therefore,

programming via the function matrix must be enabled separately.

Access - Status

read only

Use this parameter to display the current status of the possibilities for
accessing the manufacturer-specific parameters of the device.

User interface:

• LOCKED (parameterization disabled)
• ACCESS CUSTOMER (parameterization enabled)
• ACCESS SERVICE (parameterization enabled, access to service level)

«
...
88
89
90
91
92
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: Galeo Страницы: 19

Бренд: zenitech Страницы: 16

Бренд: Ecco Страницы: 9

Бренд: Ecco Страницы: 9

Бренд: Patton electronics Страницы: 8

Бренд: Harbor Freight Tools Страницы: 4

Бренд: IFM Electronic Страницы: 16

Бренд: IFM Electronic Страницы: 6

Бренд: kaarta Страницы: 29

Бренд: Lastolite Страницы: 3

Бренд: Tait Страницы: 46

Бренд: Tait Страницы: 9

Бренд: Tait Страницы: 89

Бренд: Tait Страницы: 20

COPENHAGEN WHEEL

Бренд: Superpedestrian Страницы: 52

Бренд: Hussmann Страницы: 10

Бренд: Acebil Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды