Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 130

background image

5 Block USER INTERFACE

Device Functions Proline Promag 55 FOUNDATION Fieldbus

28

Hauser

100%-VALUE
(2401)

!

Note!

This function is not available unless one of the following was selected in the ASSIGN
function (2400):
• VOLUME FLOW IN %
• MASS FLOW IN %
• VOLUME FLOW BARGRAPH IN %
• MASS FLOW BARGRAPH IN %

Use this function to define the flow value to be shown on the display as the 100% value.

User input:

5-digit floating-point number

Factory setting:

Nominal diameter and country dependent

FORMAT
(2402)

!

Note!

This function is not available unless a number was selected in the ASSIGN function
(2400).

Use this function to define the maximum number of places after the decimal point
displayed for the reading in the additional line.

Options:

XXXXX. - XXXX.X - XXX.XX - XX.XXX -X.XXXX

Factory setting:

X.XXXX

!

Note!

• Note that this setting only affects the reading as it appears on the display, it has no

influence on the accuracy of the system's calculations.

• The places after the decimal point as computed by the measuring device cannot always

be displayed, depending on this setting and the engineering unit. In these instances an
arrow appears on the display between the measured value and the engineering unit
(e.g. 1.2

→

kg/h), indicating that the measuring system is computing with more

decimal places than can be shown on the display.

DISPLAY MODE
(2403)

!

Note!

This function is only available if VOLUME FLOW BARGRAPH IN % or MASS FLOW
BARGRAPH IN % was selected in the function ASSIGN (2400).

Use this function to define the format of the bar graph.

Options:

STANDARD (Simple bar graph with 25 / 50 / 75% gradations and integrated sign).

A0001258

SYMMETRY (Symmetrical bar graph for positive and negative directions of flow, with
–50 / 0 / +50% gradations and integrated sign).

A0001259

Factory setting:

STANDARD

Function description

USER INTERFACE

→

ADDITIONAL LINE

→

CONFIGURATION

«
...
26
27
28
29
30
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: Ranger design Страницы: 6

Бренд: FeiYu Tech Страницы: 34

My first Walker

Бренд: Jamara Страницы: 4

Бренд: Jalousie-Welt Страницы: 20

Бренд: Paradyne Страницы: 4

651665 00 22-00-40

Бренд: hepco & becker Страницы: 5

Бренд: Thule Страницы: 4

Бренд: Sable Страницы: 15

Бренд: AOR Страницы: 29

Бренд: EVA Logik Страницы: 2

Бренд: Lexicon Страницы: 32

Бренд: Whispbar Страницы: 77

Бренд: Logik Страницы: 52

Бренд: Raytel LLC Страницы: 40

Бренд: U.S. General Страницы: 4

Бренд: Pilz Страницы: 8

COLIBRI ONE DRO

Бренд: BEA Страницы: 4

Бренд: Chef's Choice Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды