Endress+Hauser Memosens CFS51 Скачать руководство пользователя страница 37

Страница: 37 / 44

Memosens CFS51

Maintenance

Hauser

10.1.3 Cleaning the sensor

Sensor fouling can affect the measurement results and even cause a malfunction.

‣

To ensure reliable measurements, clean the sensor at regular intervals. The frequency

and intensity of the cleaning process depend on the medium.

Clean the sensor:

• As specified in the maintenance schedule

• Before every calibration

• Before returning it for repair

Type of contamination

Cleaning measure

Dirt particles on the sensor window

‣

Wipe the sensor window with a soft cleaning cloth.

Deposit buildup on the sensor
window

There may be deposit buildup in the non-visible range (UV). Therefore,
always clean the optics.

‣

Clean away oily substances with a suitable solution, e.g. isopropyl
alcohol.

After cleaning:

‣

Rinse the sensor thoroughly with water.

10.1.4 Cleaning the assembly

‣

To ensure reliable measurement, clean and rinse the assembly regularly. The frequency

and intensity of the cleaning process depend on the medium.

Содержание Memosens CFS51













































Результаты поиска

Содержание Memosens CFS51

Отзывы:

Похожие инструкции для Memosens CFS51

Бренды по названию

Популярные бренды

Endress+Hauser Memosens CFS51, Руководство по эксплуатации

Результаты поиска

Содержание Memosens CFS51

Отзывы:

Похожие инструкции для Memosens CFS51

Бренды по названию

Популярные бренды