Endress+Hauser Memosens CFS51 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 44

background image

Electrical connection

Memosens CFS51

24

Hauser

6.3

Post-connection check

Device health and specifications

Action

Is the outside of the sensor, assembly or cable free
from damage?

‣

Perform a visual inspection.

Electrical connection

Action

Are the mounted cables strain-relieved and not
twisted?

‣

Perform a visual inspection.

‣

Untwist the cables.

Is a sufficient length of the cable cores stripped, and
are the cores positioned in the terminal correctly?

‣

Perform a visual inspection.

‣

Pull gently to check they are seated correctly.

Are all screw terminals tightened?

‣

Tighten the screw terminals.

Are all cable entries mounted, firmly tightened and
leak-tight?

‣

Perform a visual inspection.

In the case of lateral cable entries:

‣

Point cable loops downward so that water can drip
off.

Are all cable entries mounted on the side or pointing
downwards?

«
...
22
23
24
25
26
...
»

Содержание Memosens CFS51













































Отзывы:

Нет отзывов

Похожие инструкции для Memosens CFS51

Бренд: Icare Страницы: 3

Бренд: HANYOUNG NUX Страницы: 4

Бренд: jenway Страницы: 30

Бренд: National Meter & Automation Страницы: 24

Бренд: Lakeshore Страницы: 2

Бренд: Kamstrup Страницы: 4

Бренд: B meters Страницы: 18

Бренд: B meters Страницы: 14

Бренд: Bamo Страницы: 8

Бренд: FARMSCAN Страницы: 28

Бренд: Keithley Страницы: 138

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

HF Scientific AccUView LED Ex

Бренд: Watts Страницы: 2

Бренд: X-Rite Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды