Endress+Hauser Liquisys M CCM223, Руководство по эксплуатации

Страница: 112 / 124

Appendix Liquisys M CCM223/253
112 Hauser
a0002635-en
R263
P114
R283
R243
R233
R213
R273
R264
P115
R284
R244
R234
R214
R2(7)
R2(6)
P111
R2(8)
R2(4)
R2(3)
R2(1)
R271
R261
P112
R281
R241
R231
R211
R262
P113
R282
R242
R232
R212
P1(1)
R1
P
R
R272
E141
E131
E121
S2
E142
E132
E122
S1
E1(4)
E1(3)
E1(2)
S S4 S5 S3
E143 E144
E133 E134
E123 E124
E113 E114 E111 E112 E1(1) E
CHECK
RELAY
Select alarm threshold
monitoring
Low; High
LoHi; Lo!; Hi!; LoHi!
Off;
Select contact to
be configured
Rel2; Rel3; Rel4 Rel1;
Select start pulse
i+ext = in external
ext = external i+stp = int. w. suppression by ext.
int = internal
Define rinse time
0 ... 999 s 30 s
Define pause time
1 ... 7200 min
360 min
Define minimum
pause time
1 ... 3600 min
120 min
Set lower
alarm threshold
0 ... 19.9 (4.9) mg/l
0.00 mg/l
Enter setpoint
0 ... 20 (5) mg/l
0.5 (0.1) mg/l
Enter control
gain Kp
0.01 ... 100.00 1.00
Enter integral action time
Tn (0.0 = no I comp.)
0.0 ... 999.9 min 0.0 min
Enter integral action time
Tn (0.0 = no I comp.)
0.0 ... 999.9 min 0.0 min
Enter control
gain Kp
0.01 ... 100.00 1.00
Enter setpoint
0 ... 20 (5) mg/l
0.5 (0.1) mg/l
Enter switch-on
temperature
0 ... 50 °C 50 °C
Enter switch-off
temperature
0 ... 50 °C 50 °C
Set pick-up
delay
0 ... 2000 s 0 s
Set pick-up
delay
0 ... 2000 s 0 s
Select switch-on point
of contact
0 ... 20 (5) mg/l
20 (5) mg/l
Select switch-off point
of contact
0 ... 20 (5) mg/l
20 (5) mg/l
Set upper
alarm threshold
0.1 ... 20 (5) mg/l
20.00 (5.00) mg/l
Enter pre-rinse time
0 ... 999 s 20 s
Chlorine / ClO2
Switch function R2(7)
on or off
On Off;
Clean =
Chemoclean
(only with Rel3 and Rel4)
Switch function R2(6)
on or off
On Off;
Timer
Switch function R2(8)
on or off
On Off;
3-point step controller
Cl2 / ClO2
(only with Rel3 and Rel4)
Switch function R2(4)
on or off
On; Basic; PID+B Off;
PID controller
Cl2 / ClO2
Switch function R2(3)
on or off
On; Basic; PID+B Off;
LC °C =
Limit contactor
T
Switch contact R2(1)
on or off
On Off;
LC PV =
limit contactor
Cl2 / ClO2
Alarm delay
0 ... 2000 min (s)
(dep. on F2)
0 min (s)
SERVICE
E+H SERVICE
Module software
SW Version
Hardware version
HW Version
Serial number
is displayed
Module identification
is displayed
Module
is displayed
identification
Module
is displayed
identification
Module
is displayed
identification
Serial number
is displayed
Serial number
is displayed
Serial number
is displayed
Hardware version
HW Version
Hardware version
HW Version
Hardware version
HW Version
Module software
SW Version
Module software
SW Version
Instrument software
SW Version
Rel (= relay)
Main (= mainboard)
Trans (= transmitter)
Contr (= controller)
Manual Hold
On Off;
Enter Hold
0 ... 999 s
dwell time
10 s
Enter SW upgrade
release code (Plus pack.)
0 ... 9999 0
Select language
GER; FRA;
ITA; NEL; ESP
ENG;
Configure Hold
CAL = with Cal.
Setup = for param. no
S+C = for param. + cal.
= no Hold
Select process
monitoring
AC; CC; AC CC
AC!; CC!; ACCC!
Off;