Endress+Hauser Liquiphant FTL64 Скачать руководство пользователя страница 60

Страница: 60 / 64

Technical data

Liquiphant FTL64

Hauser

14.4 Process

14.4.1 Process temperature range

• –60 to +230 °C (–76 to +446 °F)

• –60 to +280 °C (–76 to +536 °F)/to 300 °C (572 °F) for max. 50 h on cumulative basis

• –50 to +230 °C (–58 to +446 °F) with PFA coating (conductive)

The device can be ordered for use in very aggressive media with a highly corrosion-

resistant PFA coating. At medium temperatures up to ≥ 150 °C (302 °F), pay attention

to the chemical durability and the increasing risk of damage to the coating from

diffusion.

Observe pressure and temperature dependency,

see the "Process pressure range of the

sensors" section.

14.4.2 Medium conditions

The service life of the device can be impacted in applications where increased hydrogen

diffusion through the metallic membrane can be expected.

Typical conditions:

• Temperature: > 180 °C (356 °F)

• Pressure: > 64 bar (928 psi)

14.4.3 Thermal shock

Without restrictions within the process temperature range.

With PFA coating (conductive): ≤ 120 K/s

14.4.4 Process pressure range

WARNING

The maximum pressure for the device depends on the lowest-rated element, with

regard to pressure, of the selected component. This means that it is necessary to pay

attention to the process connection as well as the sensor.

‣

For pressure specifications, see the "Mechanical construction" section.

‣

Only operate the device within the specified limits!

‣

The Pressure Equipment Directive (2014/68/EU) uses the abbreviation "PS". The

abbreviation "PS" corresponds to the MWP (maximum working pressure) of the device.

Refer to the following standards for the permitted pressure values of the flanges at higher

temperatures:

• pR EN 1092-1: With regard to its stability-temperature property, the material 1.4435 is

identical to 1.4404, which is classed as 13E0 in EN 1092-1 Tab. 18. The chemical

composition of the two materials can be identical.

• ASME B 16.5

• JIS B 2220
In each case, the lowest value from the derating curves of the device and the selected

flange applies.

Devices with CRN approval: maximum 90 bar (1

305 psi) for devices with a pipe

extension. Information on the Hauser website:

www.endress.com

→

Downloads.

Содержание Liquiphant FTL64

































































Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды

Endress+Hauser Liquiphant FTL64, Руководство по эксплуатации

Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды