Endress+Hauser Liquiphant FTL64 Скачать руководство пользователя страница 15

Страница: 15 / 64

Liquiphant FTL64

Mounting

Hauser

5.2

Mounting the device

5.2.1

Required tool

• Open-ended wrench for sensor installation

• Allen key for housing locking screw

5.2.2

Installation

Align the tuning fork using the marking

The tuning fork can be aligned using the marking in such a way that the medium drains

off easily and buildup is avoided.
Markings may include the following:

• Material information, thread name or circle on the hexagonal nut

• II symbol on the back of the flange

316

L/G1

A0042348

 11

Markings to align the tuning fork

Installing in pipes

• Flow velocity up to 5 m/s with a viscosity of 1 mPa⋅s and density of 1 g/cm

(SGU).

Check for correct functioning in the event of other process medium conditions.

• The flow will not be significantly impeded if the tuning fork is correctly aligned and the

marking is pointing in the direction of flow.

• The marking is visible when installed.

A0034851

 12

Installation in pipes (take fork position and marking into consideration)

Screwing in the device

• Turn by the hex bolt only, 15 to 30 Nm (11 to 22 lbf ft)

• Do not turn at the housing!

Содержание Liquiphant FTL64

































































Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды

Endress+Hauser Liquiphant FTL64, Руководство по эксплуатации

Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды