Endress+Hauser Liquiphant FTL64 Скачать руководство пользователя страница 49

Страница: 49 / 64

Liquiphant FTL64

Repair

Hauser

12.1.2 Repair of Ex-certified devices

WARNING

Incorrect repair can affect electrical safety!

Explosion Hazard!

‣

Only specialist personnel or the Hauser service team may carry out repairs on

Ex-certified devices.

‣

Relevant standards and national regulations on hazardous areas, safety instructions

and certificates must be observed.

‣

Use only original Hauser spare parts.

‣

Please note the device designation on the nameplate. Only identical parts may be used

as replacements.

‣

Carry out repairs according to the instructions.

‣

Only the Hauser service team is permitted to modify a certified device and

convert it to another certified version.

‣

All repairs and modifications must be documented.

12.2 Spare parts

• Some replaceable device components are identified by a spare part nameplate. This

contains information about the spare part.

• All the spare parts for the measuring device, along with the order code, are listed in the

W@M Device Viewer

(

www.endress.com/deviceviewer

) and can be ordered. If available,

users can also download the associated Installation Instructions.

Device serial number or QR code:

Located on the device and spare part nameplate.

12.3 Return

The requirements for safe device return can vary depending on the device type and

national legislation.

1. Refer to the web page for information:

http://www.endress.com/support/return-material

 Select the region.

2. Return the device if repairs or a factory calibration are required, or if the wrong

device was ordered or delivered.

12.4 Disposal

If required by the Directive 2012/19/EU on waste electrical and electronic equipment

(WEEE), the product is marked with the depicted symbol in order to minimize the

disposal of WEEE as unsorted municipal waste. Do not dispose of products bearing this

marking as unsorted municipal waste. Instead, return them to the manufacturer for

disposal under the applicable conditions.

12.5 Battery disposal

• The end user is legally obliged to return used batteries

• The end user can return old batteries or electronic assemblies containing these batteries

free of charge to Hauser

Содержание Liquiphant FTL64

































































Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды

Endress+Hauser Liquiphant FTL64, Руководство по эксплуатации

Результаты поиска

Содержание Liquiphant FTL64

Отзывы:

Похожие инструкции для Liquiphant FTL64

Бренды по названию

Популярные бренды