Endress+Hauser Flowfit CYA27 Скачать руководство пользователя страница 42

Страница: 42 / 52

Repair

Flowfit CYA27

Hauser

Description and contents

Order No.

Kit CYA27 cable 10 m non-Ex
for flow switch or status indication light

71486872

Kit CYA27 cable 10 m Ex
for flow switch Cl. I Div.2

71486877

Kit CYA27 tool set

71486881

Kit CYA27 cleaning brush set

71486882

Kit CYA27 sealing set complete

71486884

Kit CYA27 2x manual valve inlet/outlet PVC

71486885

Kit CYA27 2x manual valve inlet/outlet PVDF

71488273

Kit CYA27 module clamp with screws
with counterpart for wall-mounting

71486888

Kit CYA27 set of blind plugs

71486889

Kit CYA27 2x spare flow body

71486892

10.2 Return

The product must be returned if repairs or a factory calibration are required, or if the

wrong product was ordered or delivered. As an ISO-certified company and also due to legal

regulations, Hauser is obliged to follow certain procedures when handling any

returned products that have been in contact with medium.

To ensure the swift, safe and professional return of the device:

‣

Refer to the website

www.endress.com/support/return-material

for information on the

procedure and conditions for returning devices.

10.3 Disposal

Electronic components may be used in the product. The product must be disposed of as

electronic waste.

‣

Observe the local regulations.

If required by the Directive 2012/19/EU on waste electrical and electronic equipment

(WEEE), the product is marked with the depicted symbol in order to minimize the

disposal of WEEE as unsorted municipal waste. Do not dispose of products bearing this

marking as unsorted municipal waste. Instead, return them to Hauser for

disposal under the applicable conditions.

Содержание Flowfit CYA27





















































Результаты поиска

Содержание Flowfit CYA27

Отзывы:

Похожие инструкции для Flowfit CYA27

Бренды по названию

Популярные бренды

Endress+Hauser Flowfit CYA27, Руководство по эксплуатации

Результаты поиска

Содержание Flowfit CYA27

Отзывы:

Похожие инструкции для Flowfit CYA27

Бренды по названию

Популярные бренды