Endress+Hauser Flowfit CYA27 Скачать руководство пользователя страница 24

Страница: 24 / 52

Installation

Flowfit CYA27

Hauser

Connecting cable

Green (GN)

DIO module, port 1, terminal 48

Distributor terminal (3)

Distributor terminal (4)

not connected

5.4.2

Settings on the CM44x

Activating the binary input of the flow switch

1. Go to

Menu/Setup/Inputs/Binary input x:1

and enable

Binary input

2. Set

Signal type: Static signal, Signal level: Low

3. Assign a limit contactor to the binary input in:

Menu/Setup/Basic setup/Limit

switches

with the options

Source of data: Binary input x:1, Operating mode:

Above limit check, Function: On

Activating the relay for the status indication light

Depending on the relay used, the following options can be used to activate the connected

relay:

•

Alarm relay:

No action necessary if the alarm relay has already been activated and the

following has been configured:

Function: Diagnostics, Operating mode: Namur F

•

2R/4R module:

Menu/Setup/Basic setup/Relay x:1

, settings:

Function

Diagnostics

Operating mode

Namur F

When using the alarm relay, it is no longer available for other messages.

Activation/assignment of flow switch for status indication light

‣

Reconfigure the diagnostic message for the limit contactor (S910) in

Menu/Setup/

Basic setup/Diagnostics settings/Diag. behavior/S910 Limit switches/Status

signal/Failure (F)

 The status of the limit contactor and thus the flow rate in the assembly is available

as a process value for all outputs of the transmitter. As soon as the flow rate is

insufficient,

F910 Limit switches

is displayed on the device along with a red screen

and a red status indication lamp on the assembly.

Any other error on the transmitter that results in a red screen will also result in a red

status display on the assembly.
The status indication light indicates the flow status only if the flow switch was also

ordered. The status indication light on its own can also be used for the NAMUR status

of the measuring system (transmitter and connected measuring devices/sensors).

Содержание Flowfit CYA27





















































Результаты поиска

Содержание Flowfit CYA27

Отзывы:

Похожие инструкции для Flowfit CYA27

Бренды по названию

Популярные бренды

Endress+Hauser Flowfit CYA27, Руководство по эксплуатации

Результаты поиска

Содержание Flowfit CYA27

Отзывы:

Похожие инструкции для Flowfit CYA27

Бренды по названию

Популярные бренды